SwiftTools

Caulk Calculator

120 linear feet of quarter-inch joint takes 6 standard 10.1-ounce tubes of caulk with the usual 15% waste allowance — each tube covers 24.3 feet at that bead size. Enter your joint length and bead size below for the exact tube count.

Your caulking job
tube volume = fl oz × 1.8047 cu in · coverage per tube = tube volume ÷ (width × depth) ÷ 12 ft · tubes = ceil(total length × (1 + waste) ÷ coverage)

A caulk bead is treated as a rectangular ribbon: its cross-section is bead width times bead depth, and one US fluid ounce is 1.8047 cubic inches, so a standard 10.1 fl oz cartridge holds 18.2 cubic inches. At a 1/4 by 1/4 inch bead that is 18.2 / 0.0625 = 291 inches, or 24.3 feet per tube. Depth should be about half the width — 1/4 inch deep in a 1/2 inch joint — with 1/4 inch a practical minimum and 1/2 inch a maximum.

Backer rod: in a joint wider than about 1/4 inch, or deeper than about 1/2 inch, set the depth with foam backer rod pushed in to a fixed depth — never fill the cavity solid. The bead must bond to two faces, not three: if caulk touches the back of the joint as well as both sides, it cannot stretch. Estimates only — read your tube: coverage varies by product, and a round or fillet bead uses far less than a rectangular one.

How the caulk calculator works

Caulk is sold by volume and applied as a bead, so the whole calculation turns on the size of that bead. A bead is treated as a rectangular ribbon: its cross-section is bead width times bead depth, and the tube volume divided by that area gives the length one tube can lay down. One US fluid ounce is 1.8047 cubic inches, so a standard 10.1 fl oz cartridge holds 18.2 cubic inches — at a 1/4 by 1/4 inch bead (0.0625 sq in) that is 18.2 / 0.0625 = 291 inches, or 24.3 feet per tube. Divide your total joint length by that coverage, add waste, and round up: 120 feet at 24.3 feet per tube is 4.94 tubes, and with 15% waste it is 5.68, so buy 6.

The bead size is squared, which catches people out. Going from a 1/4 inch bead to a 1/2 inch bead doubles the width but quadruples the volume — the same tube drops from 24 feet to 6. The coverage table tells the story: a 1/8 by 1/8 inch bead runs 97 feet per 10.1 oz tube, 3/16 by 3/16 runs 43 feet, 1/4 by 1/4 runs 24 feet, 3/8 by 3/8 runs 11 feet, and 1/2 by 1/2 runs 6 feet. A small tube (5.5 oz) covers about half the standard, and a 28 oz sausage pack about two and three-quarter times.

Bead shape changes the number too. A round bead laid on a surface has a cross-section of pi times radius squared — a 3/16 inch round bead is 0.0276 square inches, which matches the 55 feet per tube that DAP's Alex Plus data sheet gives for a 3/16-inch diameter bead. A triangle corner fillet tooled flat is half the rectangle: a 1/4 inch fillet is 0.03125 square inches. To model a round bead here, enter the diameter as the width and 0.785 times the diameter as the depth.

Worked example, the other end of the scale: 50 feet of joint at 3/8 by 3/8 inches is 50 x 12 x 0.1406 = 84.4 cubic inches, and 84.4 / 18.2 = 4.63, so buy 5 cartridges. And a 5 ft tub in a 30-inch-deep alcove has 5 + 2.5 + 2.5 = 10 feet of joint; as a 1/4 inch corner fillet (1/4 wide by 1/8 deep) that is 10 x 12 x 0.25 x 0.125 = 3.75 cubic inches, about a fifth of one tube.

Common mistakes: measuring the gap you hope to see instead of the gap that is there — check several spots, including the widest; filling a deep joint solid instead of using backer rod, which bonds the caulk on three faces so it cannot stretch and cracks; and caulking a wet or dusty surface, which peels within months. The 2:1 rule is the design to remember: depth about half the width, never deeper than 1/2 inch, and backer rod sets the depth where the joint is deep.

coverage per tube = (fl oz x 1.8047) / (width x depth) / 12 ft · tubes = ceil(total length x (1 + waste) / coverage) · 10.1 fl oz = 18.2 cu in · 1/4 x 1/4 in bead = 24.3 ft per tube

Related tools

Measure the trim first with the Baseboard Calculator, the tile joints with the Tile Grout Calculator, and the backsplash with the Backsplash Tile Calculator. Paint over latex caulk with the Paint Calculator.

Caulk calculator FAQ

How many feet does a tube of caulk cover?

It depends on the bead: a standard 10.1 fl oz tube covers about 97 ft at a 1/8 by 1/8 inch bead, 43 ft at 3/16 by 3/16, 24.3 ft at 1/4 by 1/4, 10.8 ft at 3/8 by 3/8, and 6.1 ft at 1/2 by 1/2 inch. Coverage is the tube volume divided by the bead cross-section.

How many tubes of caulk do I need for 120 feet?

At a 1/4 by 1/4 inch bead, 6 standard 10.1 oz tubes with the usual 15% waste allowance — 120 feet is 4.94 tubes before waste and 5.68 after. At a 1/2 inch bead the same 120 feet needs 23 tubes, because doubling the bead quadruples the volume.

What size caulk bead should I use?

Match the bead to the gap, with depth about half the width — the 2:1 rule. A 1/4 inch joint takes a 1/4 inch wide bead about 1/8 to 1/4 inch deep; depth should never exceed 1/2 inch, and 1/4 inch is the practical minimum.

Do I need backer rod for caulk?

Yes, in a joint wider than about 1/4 inch or deeper than about 1/2 inch. Foam backer rod pushed in to a fixed depth sets the bead depth and stops the caulk bonding to the back of the joint — a three-sided bond cannot stretch, so it cracks.

Silicone or acrylic latex caulk — which one?

Silicone for wet areas: tubs, showers, and exterior joints that must stay flexible and waterproof. Acrylic latex for interior trim, baseboards, and anywhere you need to paint over it — silicone cannot be painted.

Can you paint over caulk?

Acrylic latex caulk, yes — it is made to be painted once cured. Silicone caulk, no — paint will not stick to it, so use latex anywhere the joint will be painted.

How long does caulk last?

Five to ten years on a well-prepared joint, less in wet or sun-exposed spots. Replace it when it cracks, peels, or pulls away from one face — a failed bead lets water behind the surface it was meant to protect.