Deck Screws Calculator
Enter your deck size, board width and joist spacing, and this deck screws calculator returns the screws to buy, their weight and the boxes — using two screws at every board-to-joist crossing, the minimum the code asks for.
Planning estimate for face-screwed or hidden-clip decking. The IRC asks for at least two fasteners per board at each joist; some lumber guides add a third for boards wider than 6 inches to hold them flat — that is trade advice, not code, so check your decking guide. Screws per pound vary by brand, head and coating by 10% or more; the box label has the real count.
How the deck screws calculator works
Screws are counted from the geometry, not from the area. First count the rows of boards: the deck width in inches divided by the board width plus the gap, rounded up. Then count the joists: the deck length in inches divided by the spacing, plus one for the starting joist. Every place a board crosses a joist is a fastening point, and each point takes two face screws — the minimum the IRC asks for — or one hidden clip. Multiply crossings by screws per crossing, add waste for drops and stripped screws, and the box count follows from the screws per pound of the size you picked.
Worked example: a 20 by 12 foot deck of 5.5-inch boards with 3/16-inch gaps on joists 16 inches on centre has 144 divided by 5.6875, or 26 rows of boards, and 240 divided by 16 plus 1, or 16 joists — 416 crossings. At two screws per crossing that is 832 screws, and with 10% extra, 916 screws. At about 73 screws per pound for #10 by 2-1/2-inch screws that is about 13 pounds, or 3 boxes of 5 pounds. As a rule of thumb that is about 3.5 screws per square foot at 16-inch spacing.
Common mistakes: counting screws by the square foot alone (the count moves with board width and joist spacing, so a rule of thumb can be a third out); forgetting the plus-one joist, which undercounts every row; and ignoring butt joints — where two board ends meet on a shared joist, each end takes its own pair, so a deck cut from short boards needs more screws than this count, which assumes full-length boards. Hidden fastener systems for grooved composite boards use one clip per crossing instead of screws, so check your system’s coverage per box. The Deck Boards Calculator counts the boards these screws hold down.
rows = ceil(width in inches / (board width + gap)) · joists = floor(length in inches / spacing) + 1 · screws = rows x joists x screws per crossing x (1 + waste%)
Related tools
Also try the Deck Boards Calculator for the boards, the Deck Joist Span Calculator for the joists, and the Deck Material List Calculator for the whole takeoff.
Deck screws calculator FAQ
How many deck screws do I need per square foot?
About 3.5 screws per square foot with 5.5-inch boards and joists 16 inches on centre, including 10% extra; about 4.6 at 12-inch spacing. Work it from the geometry, not the rule of thumb — board width and spacing move the count.
How many screws go in each board at each joist?
Two face screws, the minimum the IRC asks for. Some lumber guides add a third for boards wider than 6 inches to hold them flat — that is trade advice, not code, so check your decking guide. Hidden clips take one per crossing.
What size deck screws should I use?
2-1/2 inches for 5/4 boards and 3 inches for 2x decking, so at least 1-1/2 inches of thread goes into the joist. #10 is the common size; #8 suits lighter boards. Use exterior-coated or stainless screws for pressure-treated lumber.
How many deck screws are in a pound?
About 73 per pound for #10 by 2-1/2-inch screws and about 86 for #8 by 2-1/2-inch. Counts vary by brand, head and coating by 10% or more — the box label has the real count.
How many boxes of deck screws do I need?
Divide the screw count by the screws per pound to get the weight, then divide by the box size and round up. A 20 by 12 foot deck needs about 13 pounds, or 3 boxes of 5 pounds.
Do butt joints need extra screws?
Yes. Where two board ends meet on a shared joist, each end takes its own pair of screws, so a deck cut from short boards needs more than the full-length-board count this calculator gives. Add a few percent if your boards are joined.
Should I use screws or hidden clips?
Face screws are cheaper and suit wood decking; hidden clips suit grooved composite boards and leave a clean surface with no visible fasteners. Clips take one per crossing instead of two screws, but cost more per fastener.