Concrete Footing Calculator
Enter your strip, pad or pier footing sizes, and this concrete footing calculator returns the cubic yards to order, the bag count and the cost — with the waste allowance a real trench needs.
Planning estimate, not a structural design: IRC R403.1.1 sets a 6-inch minimum footing thickness, and footing bottoms must sit below the local frost line or frost heave will lift the structure. Residential footings typically use two continuous #4 rebar bars and 2,500 to 3,000 psi concrete. Confirm sizes, depth and reinforcement with your building department and any engineer on the job.
How the concrete footing calculator works
A footing is a rectangular prism, so the volume is length times width times depth — with the inches converted to feet. A strip footing is one long run: 40 feet long, 16 inches wide and 12 inches deep is 40 times 1.333 times 1, or 53.33 cubic feet. Divide by 27 for cubic yards. Pads are the same formula per pad times the count, and round piers use pi times radius squared times height. Add 10% for trench overdig and spillage — more on an unformed earth trench — and round the order up to the next quarter yard, which is how ready-mix plants sell it.
Worked example: a 40-foot strip footing, 16 inches wide and 12 inches deep, needs 53.33 cubic feet, or 1.98 cubic yards neat. With 10% waste that is 2.17 cubic yards, so order 2.25. Bagged, that is about 102 bags of 80-pound mix at 0.60 cubic feet per bag, and the concrete weighs about 9,000 pounds. At $150 a cubic yard the ready-mix costs about $338.
Common mistakes: ordering the neat volume with no waste, then running short mid-pour; using bag yields from the wrong bag size (an 80-pound bag yields 0.60 cubic feet, a 60-pound bag 0.45, a 40-pound bag 0.30); and pouring footings shallower than the frost line — in the northern US that is 42 to 60 inches deep, and a shallow footing heaves every winter. Footings are usually at least 1.5 times as wide as the wall they carry, and at least 6 inches thick per IRC R403.1.1. The Rebar Calculator sizes the two continuous #4 bars most residential footings use.
strip: volume = length x width x depth / 144 / 27 cu yd · pad: volume = length x width x depth / 1728 x qty · pier: volume = π x (diameter / 2)² x height / 1728 x qty · order = neat x (1 + waste%), rounded up to the next quarter yard
Related tools
Also try the Concrete Cubic Yard Calculator for slabs, the Rebar Calculator for footing steel, and the Post Hole Concrete Calculator for fence posts.
Concrete footing calculator FAQ
How much concrete do I need for a 40-foot footing?
A 40-foot strip, 16 inches wide and 12 inches deep, needs 1.98 cubic yards neat — order 2.25 cubic yards with 10% waste, or about 102 bags of 80-pound mix.
How many bags of concrete per cubic yard?
45 bags of 80-pound mix (0.60 cu ft each), 60 bags of 60-pound mix (0.45 cu ft each), or 90 bags of 40-pound mix (0.30 cu ft each) per cubic yard.
How deep should a footing be?
The bottom must sit below your local frost line: 0 to 12 inches in the deep South, 12 to 24 inches in the Mid-Atlantic, and 42 to 60 inches or more in the northern US. The footing itself is at least 6 inches thick per IRC R403.1.1.
How wide should a footing be?
At least 1.5 times the wall thickness it carries — a 16-inch footing under an 8-inch wall is the common residential size. IRC Table R403.1(1) sets minimums by soil bearing capacity and storey count.
How much rebar goes in a footing?
Residential footings typically use two continuous horizontal #4 bars. Pad footings use a rebar grid in both directions, and piers use vertical bars. Check your local code — some areas require more.
What strength concrete do footings need?
Typically 2,500 to 3,000 psi minimum for residential footings per ACI 318. Higher strength is used where the soil is poor or the loads are heavy.
Should I order ready-mix or bags for footings?
Ready-mix wins above about half a cubic yard — roughly 23 bags of 80-pound mix. Below that, bags are cheaper once you count the delivery fee and short-load charge on a small truck.