House Wrap Calculator
Enter your wall perimeter and height and the roll size on the label, and this house wrap calculator returns the rolls to buy — after the course lap and waste that make a labelled roll cover less wall than the package says.
House wrap only — the weather-resistive barrier (Tyvek-style) rolls, not siding or insulation. Openings are deliberately NOT subtracted: the wrap runs over windows and doors before it is cut and flashed, so the openings field is shown for reference only. Some calculators do subtract openings; this page follows the installers who do not, and says so in the guide. If your finish needs two barrier layers (some stucco specs do), double the rolls.
How the house wrap calculator works
A roll never covers its labelled area on the wall. Each horizontal course overlaps the one below it — usually 6 inches — and that overlap is lost coverage, charged against the roll width: a 9-foot roll is 108 inches wide, so a 6-inch lap costs about 5.6% of every course. A 9 by 100 foot roll labelled 900 square feet therefore delivers about 850 square feet on the wall, and a 9 by 150 foot roll labelled 1,350 delivers about 1,275. The calculator divides the gross wall area, plus a waste allowance of 10% for seams, corners and trimming, by that effective coverage, and rounds up to whole rolls — rolls are never sold in fractions.
Worked example: a ranch with 160 feet of wall, 9 feet high, has 1,440 square feet of gross wall area. With 9 by 150 foot rolls at a 6-inch lap the effective coverage is 1,275 square feet per roll, so 1,440 times 1.10, or 1,584 square feet to cover, takes 2 rolls. The same ranch on 9 by 100 foot rolls also takes 2 rolls, but with more leftover — the longer roll is the cheaper buy here. Seam tape runs about 1 linear foot per 3 to 4 square feet of wall, and cap nails about 200 to 250 per 1,000-square-foot roll.
Common mistakes: dividing by the labelled roll size instead of the effective coverage (a roll short on a big wall is a mid-project delay); and subtracting windows and doors. The sources disagree here, so this page picks one rule and states it: do NOT subtract openings, because the wrap is installed over them and cut out before flashing — the same rule the installer guides use. Other calculators subtract them and get a smaller count; either is defensible, but mixing the two silently is not. House wrap must not sit exposed to UV for more than about 90 to 120 days, so side it promptly. The Vinyl Siding Calculator counts the cladding that goes over this barrier.
gross wall = perimeter x height · effective coverage per roll = roll width x roll length x (1 - overlap / roll width) · rolls = ceil(gross x (1 + waste%) / effective coverage)
Related tools
Also try the Vinyl Siding Calculator for the cladding, the Insulation Cost Calculator for the cavity fill, and the Wall Stud Calculator for the framing.
House wrap calculator FAQ
How many rolls of house wrap do I need?
Divide your gross wall area (perimeter times height) by the roll coverage — standard Tyvek HomeWrap rolls cover 1,000 sq ft (9 by 100 ft) or 1,500 sq ft (9 by 150 ft) on the label — then add 10 to 15% for overlaps and waste and round up. A 2,000 sq ft wall area typically needs 2 to 3 rolls.
Do I subtract windows and doors from house wrap?
No, on this page. House wrap is installed over windows and doors and cut out before flashing, so the openings stay in the area. Some calculators do subtract them and get a smaller count — this page follows the installers who do not, and says so.
How much wall does a roll of house wrap really cover?
Less than the label: a 9 by 100 foot roll labelled 900 sq ft delivers about 850 sq ft after the 6-inch horizontal lap, and a 9 by 150 foot roll labelled 1,350 delivers about 1,275 sq ft. The wider the roll, the smaller the lap loss.
How much overlap does house wrap need?
About 6 inches on horizontal courses, and 6 to 12 inches on vertical end seams. The calculator charges the horizontal lap against the roll coverage; vertical seams are inside the waste allowance.
How long can house wrap stay exposed?
About 90 to 120 days of UV exposure before sunlight degrades its performance. Side the walls promptly once the wrap is up — it is a weather barrier, not a finish.
How much house wrap tape do I need?
About 1 linear foot of seam tape per 3 to 4 square feet of wall area. A 1,440 sq ft ranch needs roughly 410 linear feet. Tape every horizontal and vertical seam for a continuous barrier.
How many cap nails does house wrap take?
Roughly 200 to 250 cap nails per 1,000 sq ft roll — about 450 for a two-roll job. Cap nails (plastic-cap roofing nails) hold the wrap without tearing it; staples alone are not enough in wind.