River Rock Calculator
A 20 by 10 foot bed in 1–3 inch river rock at 4 inches deep needs 2.47 cubic yards — 3.67 tons with the 10% allowance, or 147 half-cubic-foot bags. Pick your rock size below and the calculator sets the matching depth for you.
Depth follows the rule depth is about twice the average stone size, with a 2-inch minimum — picking a rock size above sets the matching depth, and you can adjust it after. Density is 1.35 short tons per cubic yard (2,700 lb), the consensus across river rock calculators; loose river rock runs about 2,500–2,900 lb per yard, so confirm your supplier's figure on a big order.
Estimates only — not a quote. River rock is decorative, rounded stone: use it for beds, borders, and dry creek beds. For paths, patios, or anything you drive on, use the gravel calculator instead — angular stone locks together where round rock rolls.
How the river rock calculator works
River rock is ordered by weight but measured by volume, so the calculation has two steps. First, area times depth gives volume: a 20 x 10 ft bed at 4 inches is 200 x (4 / 12) / 27 = 2.47 cubic yards. Then density turns volume into tons: at the consensus 1.35 short tons per cubic yard (about 2,700 lb), that is 3.33 tons before the allowance and 3.67 tons with the recommended 10% extra for settling and edge overage.
Depth is set by stone size, not by preference. The rule the calculators agree on is depth of about twice the average stone size, with a 2-inch minimum: 3/8 to 3/4 inch river pebbles lay 2 inches deep, 3/4 to 1 1/2 inch rock lays 2.5 inches, and the common 1 to 3 inch river rock needs 4 inches — a single layer of large stone leaves the fabric showing through. Picking a size above sets the matching depth; adjust it if your supplier recommends otherwise.
Bags are for small jobs: one cubic yard is 27 cubic feet, or 54 half-cubic-foot bags. The 20 x 10 ft example needs 2.72 cubic yards with waste, which is 73.3 cubic feet, or 147 bags — past about 15 to 20 bags, bulk delivery by the ton is almost always cheaper per yard. One ton of 1–3 inch river rock covers about 60 square feet at 4 inches deep, 80 at 3 inches, and 120 at 2 inches.
Worked example, small bed: 200 square feet at 2.5 inches in 3/4 to 1 1/2 inch rock is 200 x (2.5 / 12) / 27 = 1.54 cubic yards, 1.70 with 10% extra, or 2.29 tons. And a 100 square foot bed at 3 inches in 1–3 inch rock needs about 0.93 cubic yards, 1.02 with waste, roughly 1.2 tons or 50 bags — the same arithmetic, just a smaller bed.
Common mistakes: ordering by the ton without checking depth — the same area at 2 inches needs half the stone of 4 inches, so a shallow estimate leaves the bed thin; skipping the 10% allowance, which means a second delivery fee when the load runs short; and using river rock where you drive or walk daily — rounded stone rolls underfoot and under tires, so paths and driveways want angular gravel instead.
volume (yd³) = length x width x depth (in) / 12 / 27 · tons = yd³ x 1.35 (2,700 lb/yd³) · bags = ceil(yd³ x 54) · depth ~ 2 x average stone size, minimum 2 in
Related tools
For smaller rounded stone, use the Pea Gravel Calculator; for structural stone, the Crushed Stone Driveway Calculator and the Gravel Calculator. Keep weeds down first with the Landscape Fabric Calculator.
River rock calculator FAQ
How much river rock do I need?
Multiply length by width by depth in feet, divide by 27 for cubic yards, multiply by 1.35 tons per cubic yard, and add 10% for settling. A 20 x 10 ft bed at 4 inches deep needs 2.47 cubic yards — 3.67 tons to order.
How deep should river rock be?
About twice the average stone size, with a 2-inch minimum: 2 inches for 3/8–3/4 inch pebbles, 2.5 inches for 3/4–1 1/2 inch rock, and 4 inches for 1–3 inch river rock. A single layer of large stone leaves the fabric showing.
How much does a cubic yard of river rock weigh?
About 2,500 to 2,900 pounds — the calculator uses 2,700 lb, or 1.35 short tons. One ton of 1–3 inch river rock covers roughly 120 square feet at 2 inches, 80 at 3 inches, and 60 at 4 inches.
How many bags of river rock do I need?
One cubic yard is 54 half-cubic-foot bags. A 20 x 10 ft bed at 4 inches needs 2.72 cubic yards with waste, or 147 bags. Past about 15–20 bags, bulk delivery by the ton is usually cheaper.
How much does river rock cost per ton?
Bulk river rock typically runs $40–$100 per ton depending on size, color, and region, before delivery. The calculator defaults to $65 a ton — enter your yard's quote for an exact figure.
Is river rock good for driveways?
No. River rock is rounded and rolls under tires, so it ruts and migrates. Driveways need angular crushed stone, which locks together — see the crushed stone driveway calculator. River rock belongs in beds, borders, and dry creek beds.
Do I need landscape fabric under river rock?
Yes, for beds. Fabric stops weeds from growing through the stone and keeps the rock from sinking into the soil. Lay it before the rock, overlap seams by 6 inches, and cut X-shaped slits where plants go through.