Sandbag Calculator
Enter your barrier length and height, and this sandbag calculator returns the bag count from the published US Army Corps of Engineers tiers — base bags, reserve bags, total fill weight and the approximate base width to stage on site.
Inventory planning only, not engineering. Sandbag barriers are temporary and are not watertight — water can seep through, under or around them. Above 5 feet, or where failure would endanger people or property, follow your local flood authority and emergency plan instead of this estimate.
How the sandbag calculator works
The estimate uses the bag quantities published in the US Army Corps of Engineers, St. Paul District, Flood Fight Handbook (2022): 6 bags per linear foot for a 1-foot barrier, 21 for 2 feet, 45 for 3 feet, 78 for 4 feet and 120 for 5 feet. Your requested height rounds up to the next listed tier — a 2.5-foot request is priced at the 3-foot tier — and the base is approximately three times the barrier height, which is a planning footprint, not a structural design.
Worked example: a 100-foot barrier at 1 foot needs 100 x 6 = 600 base bags, plus a 10% reserve of 60 bags, for 660 bags total. At 40 lb of fill per bag that is 26,400 lb, or 13.2 US short tons, with an approximate 3-foot base width. A 20-foot barrier at 3 feet needs 20 x 45 = 900 base bags, or 990 with a 10% reserve.
Common mistakes: interpolating a rate between tiers instead of rounding up, forgetting reserve bags for damaged or underfilled bags, and treating the count as a guarantee — sandbag walls are temporary, leak, and fail above about 5 feet. Fill bags only about half to two-thirds full so they stack and seal, and never build where failure would endanger people without following your local flood authority guidance.
tier = round height up to 1 / 2 / 3 / 4 / 5 ft · bags per foot = 6 / 21 / 45 / 78 / 120 · total = length x rate + reserve · fill weight = total x lb per bag
Related tools
Also try the Sand Calculator for bulk sand volume and weight, the Gravel Calculator for aggregate, and the French Drain Cost Calculator for permanent drainage.
Sandbag calculator FAQ
How many sandbags do I need for 100 feet?
It depends on height: 660 bags at 1 foot (600 base plus 10% reserve), 2,310 at 2 feet, 4,950 at 3 feet, 8,580 at 4 feet and 13,200 at 5 feet, using the USACE tiers and a 10% reserve.
How many sandbags per foot of wall?
Per the USACE St. Paul Flood Fight Handbook (2022): 6 per foot at 1 foot high, 21 at 2 feet, 45 at 3 feet, 78 at 4 feet and 120 at 5 feet. The rate grows faster than height because the base widens as the wall rises.
Why does my height round up to the next tier?
The USACE table lists only whole-foot tiers, and rounding up is the conservative planning choice — a 2.5-foot request is priced at the 3-foot tier so you do not run short mid-build.
How much sand do I need for my bags?
Multiply bags by fill weight: 660 bags at 40 lb need 26,400 lb (13.2 US tons) of sand. Bags are typically filled to about 35 to 40 lb — half to two-thirds full — so they stack and seal properly.
How wide is the base of a sandbag wall?
Approximately three times the barrier height as a planning footprint: about 3 feet wide for a 1-foot wall, 9 feet for a 3-foot wall and 15 feet for a 5-foot wall, before working and access space.
How high can a sandbag wall go?
The USACE table stops at 5 feet, and sandbag walls are generally only effective up to about that height. Above 5 feet, or where failure would endanger people or property, use engineered flood protection and follow local emergency guidance.
Are sandbag barriers watertight?
No — they are temporary barriers that slow water but leak through, under and around the bags. A bag count is inventory planning only; it is not an engineering design or a promise that a barrier will hold.