Metal Roofing Screws Calculator
An 800 square foot metal roof needs 640 field screws — 3 boxes of 250 — at the industry baseline of 80 screws per square, with the usual 10% spare. Enter your roof size below for the exact screw or clip count.
Field screws are the industry baseline of 80 per square — one square is 100 square feet of roof area. Screws are driven in the flat next to the rib, typically every 24 inches along the purlins, which averages out to about 80 per square. That count does not include stitch screws along the sidelaps, which add roughly 40 more per square on a panelled roof — see the guide. Standing-seam roofs hide their fasteners: one clip per panel every 24 inches up the slope, and no face screws at all.
Screws only — not panels or trim. This page counts fasteners; panel counts, cut lengths, ridge caps and underlayment come from the metal roof panel calculator. Estimates only — read your panel maker: the screw pattern, washer type and clip spacing on your panel's installation guide always win over the baseline here. Use the maker's screw, not a bin screw.
How the metal roofing screws calculator works
Exposed-fastener metal roofing is ordered by the square: field screws equals roof area divided by 100, times 80 screws per square, plus a spare allowance. One square is 100 square feet of roof area, and 80 per square is the industry baseline — screws driven in the flat next to the rib, typically every 24 inches along the purlins. On the default roof — one 50 ft plane, 16 ft of slope, 800 square feet — that is 8 squares times 80, or 640 screws, and with 10% spare 704, so buy 3 boxes of 250.
The headline count is field screws only, and the stitch screws are the part most takeoffs miss. Stitch screws run along the sidelaps where one panel overlaps the next, and they add roughly 40 more per square on a panelled roof: one worked example puts a 1,596 square foot gable roof at 1,894 screws, about 119 per square including stitch, against 1,277 field screws at 80 per square. The calculator shows the stitch line separately so you can see both numbers before you buy — order them in the same box count, or in a second box size if your supplier packs them differently.
Standing-seam roofs work differently: there are no face screws at all, and the fastener is a concealed clip, one per panel every 24 inches up the slope. Panels come from the ridge length divided by the installed coverage width — a 50 ft ridge in 36-inch coverage is 600 / 36 = 16.67, rounded up to 17 panels — and clips per panel come from the slope divided by 2 ft, so a 16 ft slope takes 8 clips per panel. That is 136 clips, 150 with the 10% spare, or 2 boxes of 100. Switch the fastener system on the calculator and it returns clips instead of screws.
Worked example at a larger scale: a 40 by 30 ft roof at 4/12 pitch is 1,200 square feet of footprint times the 1.054 pitch factor, or 1,265 square feet of roof — 12.65 squares — and at 80 screws per square with 5% waste that is 1,063 screws. The pitch factor is exact math, the square root of 1 plus (rise over 12) squared, and it matters here because the area is sloped area, not footprint: a 12/12 roof needs 41% more screws than its footprint suggests.
Common mistakes: ordering by footprint instead of sloped area, which under-orders on any pitched roof; forgetting the stitch screws, which leave you a box short on a panelled roof; and buying bin screws instead of the panel maker's screw. The washer matters as much as the count: a neoprene-washer screw seals the hole it makes, and a mismatched screw — wrong length, wrong washer, wrong metal — leaks or corrodes. Screws go in the flat next to the rib, never on the rib itself.
field screws = roof area / 100 x 80 per square · stitch screws ~40 per square extra · standing-seam clips = panels x slope / 2 ft, panels = ridge x 12 / coverage width · boxes = ceil(count x (1 + spare) / box size)
Related tools
Count the panels with the Metal Roof Panel Calculator, check the pitch with the Roof Pitch Calculator, and count the felt with the Roofing Felt Calculator. Asphalt shingles take a different fastener — see the Roofing Nails Calculator.
Metal roofing screws calculator FAQ
How many screws do I need for a metal roof?
Multiply the roof area in squares by 80 screws per square, then add spare. An 800 square foot roof is 8 squares times 80, or 640 field screws — 704 with the 10% spare, so buy 3 boxes of 250. Stitch screws along the sidelaps are extra, about 40 per square.
How many screws per square of metal roofing?
80 field screws per square is the industry baseline, driven in the flat next to the rib every 24 inches along the purlins. With stitch screws along the sidelaps, a panelled roof runs about 119 per square in total.
What are stitch screws on a metal roof?
Stitch screws fasten one panel to the next along the sidelap, where the panels overlap. They are not counted in the 80-per-square field baseline — budget about 40 more per square for them, and order them with the field screws.
How many clips does a standing seam roof need?
One clip per panel every 24 inches up the slope. A 50 ft ridge in 36-inch coverage is 17 panels, and a 16 ft slope takes 8 clips per panel — 136 clips, or 150 with the 10% spare. Standing seam has no face screws at all.
Do I measure the footprint or the sloped area?
The sloped area. The pitch factor — the square root of 1 plus (rise over 12) squared — turns footprint into roof area: 1.054 at 4/12, 1.118 at 6/12, 1.414 at 12/12. A steep roof needs far more screws than its footprint suggests.
Where do metal roofing screws go — on the rib or in the flat?
In the flat next to the rib, never on the rib itself. Screws on the rib sit proud, do not seal, and work loose. The neoprene washer under the screw head seals the hole it makes.
Can I use any screw for a metal roof?
No — use the screw your panel maker specifies, with the right length, washer and metal. A bin screw with the wrong washer leaks, and a mismatched metal corrodes against the panel. The panel maker's installation guide has the last word on the screw pattern.