SwiftTools

Paver Base Calculator

Enter your paver area and what it is for, and this paver base calculator returns the base gravel in cubic yards and tons, the bedding sand, and how deep to dig — to the ICPI depths, including the six inches of base that must extend past every edge.

Your paver area
base area = (length + 1 ft) x (width + 1 ft) — base extends 6 in past every edge · compacted cu yd = base area x depth / 324 · loose cu yd = compacted x (1 + compaction%) · tons = loose cu yd x 1.4 · bedding sand = area x 1 in / 324 · excavation = base + 1 in bedding + paver thickness

Base only — gravel, bedding sand and excavation depth. Paver counts are on the Paver Calculator and joint sand on the Paver Sand Calculator. Use crushed stone with fines (crusher run, #411, quarry process) for the base, not washed drainage stone, which never locks together. Depths are the ICPI minimums; many guides use 6 inches for a patio and 8 to 12 for a driveway, so go deeper on soft or clay soil.

How the paver base calculator works

The base is where a paver project succeeds or fails, and the pavers are just the wearing surface. The calculator starts from the ICPI depths: 4 inches of compacted crushed stone for a patio or walkway, 6 inches for heavy use, and 8 inches for a driveway, plus 2 inches on frost or clay soil. The base must extend at least 6 inches past the paver edge on every side — the ICPI rule most calculators leave out — so the base area is the paver area plus a foot in each direction. Crushed aggregate loses about 20% of its volume when compacted, so the order is the compacted volume plus the compaction allowance, at about 1.4 tons per loose cubic yard. The bedding sand is a separate 1-inch screeded course of concrete sand over the paver area only.

Worked example: a 16 by 12 foot patio (192 square feet) with a 4-inch base has a base area of 17 by 13 feet, or 221 square feet, once the 6-inch extension is added. That is 221 times 4 divided by 324, or 2.73 cubic yards compacted, and 3.27 cubic yards loose with the 20% compaction allowance — about 4.6 tons. The bedding sand is 192 divided by 324, or 0.59 cubic yards. With 60 mm pavers the total excavation is 4 plus 1 plus 2-3/8, or about 7-3/8 inches. Without the edge extension the same patio is 2.4 cubic yards compacted and 3.0 loose, which is why calculators that skip it under-order.

Common mistakes: using washed drainage stone for the base — it never locks together, so order crusher run or #411 with fines; compacting in one deep lift, which never compacts properly no matter how many passes you make (compact in 3- to 4-inch lifts instead); and laying more than 1 inch of bedding sand, which ruts under load — the sand is a leveling course, not a substitute for compacted base. Depth guides disagree: Unilock calls for 6 to 8 inches under patios and 10 to 14 under driveways, against the 4-inch ICPI minimum used here, so go deeper on soft or clay soil. The Paver Calculator counts the pavers that sit on this base.

base area = (length + 1 ft) x (width + 1 ft) · compacted cu yd = base area x depth / 324 · loose cu yd = compacted x (1 + compaction%) · tons = loose cu yd x 1.4 · bedding sand = area x 1 in / 324 · excavation = base + 1 in bedding + paver thickness

Related tools

Also try the Paver Calculator for the paver count, the Paver Sand Calculator for the joint sand, and the Gravel Calculator for other stone orders.

Paver base calculator FAQ

How deep should a paver base be?

4 inches of compacted crushed stone for a patio or walkway, 6 inches for heavy use, and 8 inches for a driveway, plus 2 inches on frost or clay soil (ICPI Tech Spec 2). Many guides use 6 inches for patios and 8 to 12 for driveways — go deeper on soft soil.

Why does the base extend past the paver edge?

The ICPI requires at least 6 inches of base past every edge so the edge restraint spikes bite into base, not soil. Without it the outer pavers spread and the edge collapses. This calculator adds a foot to each dimension for it.

How much gravel do I lose to compaction?

Crushed aggregate loses roughly 20% of its volume when properly compacted, so order about 20% more than the compacted volume — 25% on deep bases. Compact in 3- to 4-inch lifts; a single deep lift never compacts properly.

How much bedding sand do I need?

One inch, screeded, over the paver area: area in square feet divided by 324 gives cubic yards. A 16 by 12 foot patio needs about 0.59 cubic yards. Use concrete sand (ASTM C33) — coarse, washed and sharp-edged — and never more than 1 inch.

How many tons is a cubic yard of paver base?

About 1.4 tons per loose cubic yard of crushed stone with fines. A 3.27-cubic-yard order is about 4.6 tons. Compacted stone is denser — about 2 tons per cubic yard in place — so compare supplier quotes by the same basis.

How deep do I dig for pavers?

Base depth plus 1 inch of bedding sand plus the paver thickness: a patio with a 4-inch base and 60 mm (2-3/8 inch) pavers digs about 7-3/8 inches. A driveway with an 8-inch base and 80 mm pavers digs about 12-1/8 inches.

What stone should I use for a paver base?

Crusher run, #411, quarry process or ABC — crushed stone with fines in it, which compacts into a near-solid layer. Washed drainage stone like #57 never locks together and is the wrong material for a base.