Roof Valley Flashing Calculator
Two 18-foot valleys need 4 valley flashing pieces, 1 roll of ice and water shield and 1 tube of sealant. Enter your valleys below for your exact count.
Valley only — this page counts valley metal, the ice and water membrane under it, and sealant. Step flashing is counted per shingle course and is a different job; drip edge is a separate takeoff. Measure each valley along the valley line itself, from eave to ridge — it runs diagonally across two slopes, so it is always longer than the horizontal distance.
Estimates only — not a quote. Open valleys use valley metal; closed or woven valleys are shingled over and need no valley metal pieces, though the membrane still goes underneath.
How the roof valley flashing calculator works
Valley metal is ordered by length, not by the piece: total valley feet divided by the effective length of one stock piece, rounded up. Valley metal comes in 10 foot lengths lapping 6 inches, so each piece covers about 9.5 feet of run — pieces = ceil(total valley feet / 9.5). Under it goes an ice and water membrane in a 36 inch wide strip down the valley: valley feet x 3 feet wide, divided by the roll coverage of about 200 sq ft, or roughly 66.7 feet of valley per roll. Sealant runs about 1 tube per 40 linear feet of combined flashing.
Worked example: one 16 foot valley needs 16 / 9.5 = 1.68, rounded up to 2 ten-foot pieces. Two 18 foot valleys are 36 feet of valley, so 36 / 9.5 = 3.79, rounded up to 4 pieces; the membrane is 36 x 3 = 108 sq ft, or 1 roll; and sealant is 36 / 40 = 0.9, rounded up to 1 tube. A 12 foot valley is 2 pieces and 0.2 rolls of membrane; a 20 foot valley is 3 pieces; a 32 foot valley is 4 pieces and 0.5 rolls; a 48 foot valley is 6 pieces and 0.7 rolls.
Common mistakes: measuring the horizontal run instead of the valley line — the valley runs diagonally across two slopes, so it is always longer than the horizontal distance suggests; forgetting the 6 inch lap, which costs half a foot per piece; and folding step flashing into this count — step flashing is a stack of individual pieces, one per shingle course up a wall, and belongs to its own takeoff. This page is valley-only on purpose: valley metal, membrane and sealant. Open valleys use valley metal; closed or woven valleys are shingled over and need no metal pieces, though the membrane still goes underneath.
valley metal pieces = ceil(total valley ft / (stock length - 0.5 ft lap)) · ice & water = valley ft x 3 ft / 200 sq ft per roll (about 66.7 ft of valley per roll) · sealant = ceil(valley ft / 40 ft per tube)
Related tools
For the rafters that frame the valley, use the Roof Rafter Calculator; for the felt under the shingles, the Roofing Felt Calculator; and for the downspouts the valleys drain into, the Gutter Downspout Calculator.
Roof valley flashing calculator FAQ
How many valley flashing pieces do I need?
Divide the total valley feet by 9.5 — the effective length of a 10 foot piece after its 6 inch lap — and round up. Two 18 foot valleys are 36 feet, so 36 / 9.5 = 3.79, rounded up to 4 pieces.
What length do valley flashing pieces come in?
10 feet is standard, with 8 and 12 foot pieces also sold. Every piece loses about 6 inches to the lap with the piece below it, so a 10 foot piece covers 9.5 feet of valley run.
How much ice and water shield do valleys need?
A 36 inch wide strip down the whole valley: valley feet x 3 feet, divided by about 200 sq ft per roll. One roll covers roughly 66.7 feet of valley — two 18 foot valleys need 108 sq ft, or 1 roll.
How do I measure a roof valley?
Along the valley line itself, from the eave to where it meets the ridge. The valley runs diagonally across two slopes, so it is always longer than the horizontal distance between the same two points.
How much sealant do roof valleys need?
About 1 tube per 40 linear feet of valley. Two 18 foot valleys are 36 feet, so 1 tube; a long roof with 80 feet of valley needs 2 tubes.
Open valley or closed valley — does it change the count?
Yes. An open valley uses valley metal pieces, which is what this page counts. A closed or woven valley is shingled over and needs no valley metal pieces, though the ice and water membrane still goes underneath.
Does this calculator include step flashing?
No — this page is valley-only. Step flashing is counted per shingle course up a wall, one piece per course, which is a different takeoff. Valley metal, apron flashing and drip edge are all ordered by length, the same way, but each is its own count.