SwiftTools

Sprinkler Head Calculator

A 60 by 40 foot lawn with 30-foot rotors needs 9 heads drawing 27 GPM, split into 3 zones on a 10 GPM supply. Enter your lawn below for your head count, zones and run time.

Your lawn
heads along = ceil(length / spacing) + 1 · rows = ceil(width / spacing) + 1 · total heads = along x rows · zones = ceil(total x GPM per head / available GPM) · runtime = 60 / precipitation rate (min per week for 1 in)

Planning estimate for a rectangular lawn, head-to-head layout — each head throws far enough to wet the next one, which is the only way to get even coverage. Irregular lawns need their sections measured separately and added. This counts heads, zones and run time only: valves, pipe, backflow preventer, controller and trenching are not included, and the layout is not a stamped hydraulic plan — verify against your nozzle chart and local code.

How the sprinkler head calculator works

Sprinkler heads are spaced head to head: each head throws far enough to wet the next one, which is the only way to get even coverage. That fixes the spacing by head type — spray heads about 15 feet apart, rotary nozzles about 20 feet, rotors about 30 feet — and the count follows from the grid: heads along the length are the length divided by the spacing, rounded up, plus one for the head at the far edge, and the same across the width. The plus one is the step most takeoffs miss, and on a tight grid it costs several heads per direction. A rectangle gets a head at every corner, along every edge and across the middle; irregular lawns need a scale drawing, not a single rectangle.

Zones follow from flow, not from the head count: divide the total flow of all heads by the flow available at the tap, and round up. Worked example: a 60 by 40 foot lawn with 30-foot rotors needs 3 heads along (60 divided by 30, plus one) and 3 rows across (40 divided by 30, rounded up, plus one) — 9 heads in total. At 3 GPM each they draw 27 GPM, split into 3 zones of 3 heads on a 10 GPM supply, each run about 120 minutes a week to apply 1 inch of water. The same lawn with 15-foot spray heads needs 5 along and 4 across — 20 heads at 1.5 GPM, or 30 GPM — and about 40 minutes a week per zone, because spray heads put water down faster.

Common mistakes: spacing heads by their full diameter instead of their throw radius (heads farther apart than the radius leave dry spots); forgetting the plus-one head at the far edge; and putting more heads on a zone than the supply can run — heads per zone is the available flow divided by the flow of one head, rounded down, so 12 GPM runs 4 rotor heads at 3 GPM each, not 5. Run time comes from the precipitation rate: about 1.5 inches per hour for spray heads, 0.7 for rotary nozzles and 0.5 for rotors, so one inch a week takes about 40, 86 or 120 minutes respectively. Water early in the morning to cut evaporation, and check your local watering rules before you set the schedule.

heads along = ceil(length / spacing) + 1 · rows = ceil(width / spacing) + 1 · total = along x rows · zones = ceil(total x GPM per head / available GPM) · runtime = 60 / precipitation rate (min per week for 1 in)

Related tools

Also try the Lawn Square Footage Calculator to measure the lawn, the Sod Calculator for new turf, and the Mulch Calculator for the beds around it.

Sprinkler head calculator FAQ

How many sprinkler heads do I need for my lawn?

Divide the lawn by the head spacing in both directions, round up, add one each way, and multiply. A 60 by 40 foot lawn with 30-foot rotors needs 3 by 3, or 9 heads; the same lawn with 15-foot spray heads needs 5 by 4, or 20 heads.

How far apart should sprinkler heads be?

At the head's throw radius, so each head sprays to the next one: rotors about 30 feet apart, rotary nozzles about 20 feet, spray heads about 15 feet. Spacing them farther leaves dry spots between heads.

How many sprinkler heads can run on one zone?

Divide your available flow by the flow of one head and round down: with 12 GPM and rotor heads at 3 GPM each, you can run 4 heads on one zone. Six heads at 4 per zone need 2 zones.

How long should I run my sprinklers?

Long enough to apply about 1 inch of water a week: about 40 minutes a week per zone for spray heads (1.5 in/hr), about 86 for rotary nozzles (0.7 in/hr) and about 120 for rotors (0.5 in/hr). Split it into two or three waterings.

What is head-to-head sprinkler coverage?

Head-to-head means each sprinkler throws water all the way to the next head, so every part of the lawn is watered by at least two heads. It is the industry standard for uniform coverage — spacing by the full diameter instead leaves dry stripes.

Do I need a different zone for spray heads and rotors?

Yes. Never mix head types on one zone: spray heads, rotary nozzles and rotors put water down at very different rates, so one type would drown while the other stays dry. Each head type gets its own zone.

What does this calculator not include?

Heads, zones and run time only. Not included: the backflow preventer, valves, boxes, controller, wire, swing joints, fittings, pipe, trenching or the plumbing permit. Get a quote for those from your irrigation supplier.