Flagstone Calculator
A 200 square foot patio in 1.5-inch sandstone flagstone needs about 2.18 tons — 2 pallets — plus a 0.62 cubic yard sand bed and a 2.47 cubic yard gravel base. Enter your patio size and stone below for the full order.
Coverage is weight-based: one ton of 1.5-inch sandstone or limestone covers about 110 square feet, and every time thickness doubles, coverage halves — you are buying weight, and thicker stone uses more weight per square foot. Denser granite and bluestone cover about 6% less at the same thickness. Pallets are packaging, not a unit: yards load them to whatever suits their forklift, so a pallet is typically about 1.5 tons but varies by supplier — always order by the ton.
Estimates only — not a quote. The setting bed is 1 inch of sand and the gravel base is 4 inches under it; both are sized on the same patio area with no waste added. Confirm your yard's coverage per ton for the exact stone and thickness — it replaces the typical figure here. Flagstone is for patios and paths, not driveways.
How the flagstone calculator works
Flagstone is sold by weight, so the calculation starts from coverage: how many square feet one ton of stone covers at your thickness. The consensus across flagstone calculators is about 110 square feet per ton at 1.5 inches for sandstone and limestone — the most common patio stone — and coverage scales inversely with thickness: 1 inch covers about 166 square feet per ton, 2 inches about 83, and 3 inches about 55. Denser stone covers less: granite and bluestone run about 175 lb per cubic foot against sandstone's 165, so they cover roughly 6% less ground per ton at the same thickness.
Tons equals area times waste, divided by coverage. A 200 square foot patio in 1.5-inch sandstone is 200 / 110 = 1.81 tons bare; irregular stone needs 20% for cuts and offcuts, so the order is 1.81 x 1.20 = 2.18 tons. Pallets are a packaging unit, not a measurement — yards load them to about 1.5 tons, so 2.18 tons is 2 pallets. The setting bed is 1 inch of sand (200 / 324 = 0.62 cubic yards, about 0.83 tons) and the gravel base is 4 inches (200 x 4 / 324 = 2.47 cubic yards, about 3.46 tons).
One figure to ignore: a single calculator on the web implies about 15 square feet per ton, which contradicts every other source — the published yard range is 70 to 110 square feet per ton depending on thickness, and the density math (170 lb per cubic foot at 1.5 inches is 21.25 lb per square foot, or 94 square feet per ton) lands in the same band. If your yard quotes a coverage per ton for the exact stone and thickness, use their number instead of the typical figure — it is the only number that matters on delivery day.
The base is not optional. A dry-laid flagstone patio sits on 4 inches of compacted gravel and a 1-inch sand setting bed; without them the stones settle unevenly and the joints wash out. Joint gaps are the other quiet driver: irregular flagstone leaves 10% or so of the area as open joint, which is area you do not need stone for — the waste allowance for cuts roughly balances it, which is why the worked example uses the full area with 20% waste rather than subtracting joints first.
Common mistakes: ordering by pallet count instead of tons, when pallets vary by a third between yards; buying thin 1-inch stone for a path that takes foot traffic in wet weather — 1.5 inches is the standard patio thickness, and steppers should be 2 to 3 inches; and forgetting the base, which is roughly as much material by weight as the stone itself. Measure odd shapes by splitting them into rectangles and adding the parts.
coverage = 110 x (1.5 / thickness) sq ft per ton (sandstone/limestone) · tons = area x (1 + waste) / coverage · sand bed = area / 324 yd³ · gravel base = area x 4 / 324 yd³
Related tools
Count the joint sand with the Polymeric Sand Calculator, size the base with the Paver Base Calculator, and compare square-cut pavers with the Paver Calculator. Keep weeds down first with the Landscape Fabric Calculator.
Flagstone calculator FAQ
How many tons of flagstone do I need for a patio?
Divide the patio area by the coverage per ton for your thickness, then add waste. A 200 square foot patio in 1.5-inch sandstone needs 1.81 tons bare and about 2.18 tons with the 20% allowance for irregular stone — 2 pallets at 1.5 tons each.
How much flagstone does one ton cover?
About 110 square feet at 1.5 inches for sandstone or limestone, 166 at 1 inch, 83 at 2 inches, and 55 at 3 inches. Granite and bluestone are denser and cover about 6% less at the same thickness. Your yard's quote for the exact stone replaces these typical figures.
How much sand goes under flagstone?
A 1-inch setting bed: patio area divided by 324 gives cubic yards. A 200 square foot patio needs 0.62 cubic yards of sand, about 0.83 tons. The 4-inch gravel base under it is 2.47 cubic yards, about 3.46 tons.
How thick should flagstone be?
1.5 inches is the standard patio thickness. Use 1 inch only for light, dry-laid patios; 2 to 3 inches for steppers and paths that take regular foot traffic. Thinner stone cracks and thicker stone costs more per square foot because you buy by weight.
How many pallets of flagstone do I need?
A pallet is typically about 1.5 tons, so divide your tons by 1.5 and round up — 2.18 tons is 2 pallets. But pallets are packaging, not a unit: yards load them to whatever suits their forklift, so always order and pay by the ton.
Irregular or square-cut flagstone — which is cheaper?
Irregular flagstone is sold by the ton and needs about 20% waste for cuts and odd edges; square-cut stone is sold by the square foot and counted by the piece, with about 12% waste. Irregular is usually cheaper per square foot installed, square-cut is faster to lay.
Can flagstone go over concrete?
Yes, set in a mortar bed on a sound concrete slab — the usual choice for a patio that must stay perfectly level. Dry-laid flagstone on a sand bed needs the 4-inch gravel base underneath, and it will settle slightly over time.