SwiftTools

Concrete Sealer Calculator

A 1,000 square foot patio sealed with acrylic needs 6.42 gallons — 2 five-gallon pails — for two coats with the usual 10% waste allowance. Enter your surface size and sealer type below for the exact gallons and pails.

Your concrete surface
gallons = area ÷ first-coat coverage + area ÷ second-coat coverage, × (1 + waste) · pails = ceil(gallons ÷ 5) · rough surfaces cover less: broom ÷ 1.2, rough ÷ 1.4

Coverage is the figure on the label you buy, and the label prints a range because concrete varies: use the low end on rough or porous concrete. First-coat rates here are the usual figures — penetrating about 200, acrylic 300, epoxy 250, polyurethane 400 sq ft per gallon. The second coat always covers more than the first, because the first coat has already sealed the pores: acrylic is published at 300 first and 400 second, and the other types use the same roughly one-third uplift as a planning estimate. Change either rate to match your label — the label governs.

Concrete only. This page sizes sealer for patios, slabs, walkways, pool decks and garage floors. Driveways use the Driveway Sealer Coverage Calculator, and asphalt takes emulsion or coal-tar sealer, not concrete sealer — a different product with different coverage. Estimates only — read your label: recoat timing, surface prep and curing all come from the product data sheet, not this page.

How the concrete sealer calculator works

Sealer is ordered by the gallon, coat by coat, because the two coats do not cover the same area. The first coat soaks into open pores and covers less; the second coat goes onto a sealed surface and covers more. Gallons equals area divided by the first-coat coverage, plus area divided by the second-coat coverage, times one plus the waste allowance. On the default patio — 50 by 20 ft, 1,000 square feet, acrylic at 300 sq ft per gallon first coat and 400 second — that is 1,000 / 300 = 3.33 gallons plus 1,000 / 400 = 2.50, or 5.83 gallons, and with 10% waste 6.42 gallons, so buy 2 five-gallon pails.

The first-coat rates are the usual figures: penetrating and silane-siloxane sealers about 200 sq ft per gallon, acrylic about 300, epoxy about 250, polyurethane about 400. Only the acrylic pair is published coat by coat — 300 first, 400 second, from the Euclid INCRETE Clear Seal 100 data sheet — so the other second-coat rates use the same roughly one-third uplift as a planning estimate: penetrating 250, epoxy 325, polyurethane 500. Both rate fields are editable, and the rate on your label always wins over the preset.

Surface finish moves the answer as much as the product does. A broom finish drinks about 20% more sealer than a smooth troweled slab, and a rough or exposed-aggregate surface about 40% more — the calculator divides the coverage by 1.2 and 1.4 for those finishes. The same 1,000 sq ft patio in a broom finish needs 7.70 gallons instead of 6.42. The label prints a range for exactly this reason: use the low end of the range on rough or porous concrete.

Worked example at the other end of the scale: a 480 square foot area at 250 sq ft per gallon, two coats, 10% waste, is 480 / 250 x 2 x 1.10 = 4.22 gallons, so buy 5 gallons, or 1 five-gallon pail. And the quick rule from the calculators — area times coats divided by coverage, plus 5% for what stays in the roller, tray and sprayer — lands in the same place: a 20 by 40 ft area, two coats at 200 sq ft per gallon, is 800 x 1.05 x 2 / 200 = 8.4, rounded up to 9 gallons.

Common mistakes: using the optimistic high end of the label range on a thirsty slab, and coming up a gallon short; counting one coat when the product needs two — most acrylics are two-coat products, and many penetrating sealers take a second coat on porous concrete; and sealing too soon, before the concrete has cured — new concrete usually needs about 28 days, and a sealer applied early traps moisture and peels. Test a small area first: if the sealer beads and sits, the surface is not ready.

gallons = area / first-coat coverage + area / second-coat coverage, x (1 + waste) · acrylic 300/400, penetrating 200/250, epoxy 250/325, polyurethane 400/500 sq ft/gal · broom / 1.2, rough / 1.4

Related tools

Size the slab itself with the Concrete Slab Calculator, count the bags with the Concrete Bags Calculator, and keep it damp while it cures with the Concrete Curing Water Calculator. Driveways use the Driveway Sealer Coverage Calculator.

Concrete sealer calculator FAQ

How many gallons of concrete sealer do I need?

Divide the area by the coverage per coat, add the coats, then add waste. A 1,000 sq ft patio in acrylic (300 sq ft/gal first coat, 400 second) needs 3.33 + 2.50 = 5.83 gallons, or 6.42 with the 10% waste allowance — buy 2 five-gallon pails.

How far does a gallon of concrete sealer go?

About 200 sq ft per gallon for penetrating sealers, 300 for acrylic, 250 for epoxy, and 400 for polyurethane on the first coat — less on rough or porous concrete. The second coat always covers more, roughly a third more, because the first coat has sealed the pores.

How many coats of concrete sealer do I need?

Most acrylics are two-coat products; many penetrating sealers take one coat, or two on porous concrete. Epoxy and polyurethane are usually two coats as well. Follow the label — a second coat applied too soon, or skipped when the product needs it, both fail.

Does a broom finish use more sealer?

Yes — about 20% more than a smooth troweled slab, and a rough or exposed-aggregate surface about 40% more. The calculator divides coverage by 1.2 for broom and 1.4 for rough finishes. Use the low end of the label range on rough concrete.

Can I use concrete sealer on asphalt?

No — asphalt takes emulsion or coal-tar sealer, a different product with different coverage. Concrete sealer will not bond to asphalt. Driveways use the driveway sealer coverage calculator, which is sized for asphalt and concrete driveways separately.

How long after pouring can I seal concrete?

New concrete usually needs about 28 days to cure before sealing. Sealing too soon traps moisture and the sealer peels. Test a small area first: if the sealer beads and sits instead of soaking in, the surface is not ready.

How much does it cost to seal a concrete patio?

Material only: a 1,000 sq ft patio in acrylic needs 2 five-gallon pails, about $300 at $150 a pail. Penetrating sealers run $30–$70 a gallon and epoxy coatings up to $150 a gallon, so the product choice moves the total more than the area does.