Backsplash Tile Calculator
A 20 foot wall at 18 inches high needs 264 subway tiles with 10% waste — 7 boxes of 40, plus 1 bag of grout. Enter your wall below for your exact count.
Tiles and grout only — adhesive, trim pieces, sealant and removing an old backsplash are not included (see the Tile Adhesive Calculator for the adhesive). Grout here is unsanded at about 1 lb per 5 sq ft for subway tile, in 25 lb bags. Always order a full extra box as a spare — tiles from the same dye lot can be impossible to match later for repairs. Buy all the tile in one go, and from the same batch.
How the backsplash tile calculator works
A backsplash is a narrow strip, not a full wall, so the calculation starts from the run: wall area = counter length in feet times backsplash height in inches divided by 12, minus about half a square foot per outlet or switch you have to cut around. The standard kitchen gap between countertop and upper cabinets is 18 inches, which is a foot and a half, so every linear foot of counter produces 1.5 square feet of backsplash. Tiles = wall area divided by the area of one tile, times one plus the waste percentage, rounded up — then boxes = tiles divided by tiles per box, rounded up, because a store will not sell you part of a box.
Worked example: a 20 foot wall at 18 inches high is 30 sq ft. A 3 by 6 inch subway tile covers 18 square inches, or 0.125 sq ft, so 30 divided by 0.125 is 240 tiles before waste, and 264 tiles with a 10 percent allowance — 7 boxes at 40 tiles per box. An 18 linear foot counter at the same height with 15% waste needs about 278 tiles, or 7 boxes of 40. With 12 by 12 inch tiles the same 30 sq ft wall needs only 30 tiles before waste and 33 with waste. Grout is about 1 lb per 5 sq ft for subway tile in 25 lb bags, so the 30 sq ft wall takes 1 bag.
Common mistakes: using 10% waste on a subway, diagonal or outlet-heavy wall, where 12 to 15% is the right figure — backsplashes cluster near fixtures that require cuts, so the waste factor is 15% on many calculators; ordering by the exact tile count instead of whole boxes; and forgetting the grout joint — the tile count here is based on the area of each tile plus its grout joint, so it is more accurate than dividing the wall area by the tile area alone. For the adhesive, use the Tile Adhesive Calculator; for the tiles on a floor, the Tile Calculator; for the grout, the Tile Grout Calculator.
tiles = ceil(wall area / tile area x (1 + waste%)) · boxes = ceil(tiles / tiles per box) · grout = ceil(area / 5 sq ft per lb / 25 lb per bag) · waste: 10% straight, 12% brick, 15% diagonal, 20% herringbone · standard height 18 in
Related tools
Also try the Tile Calculator for floor and wall tile, the Tile Grout Calculator for grout, and the Tile Adhesive Calculator for the adhesive.
Backsplash tile calculator FAQ
How many tiles do I need for a backsplash?
Divide the wall area by the area of one tile, then add waste. A 30 square foot wall with 3 by 6 inch subway tiles, each 0.125 square feet, needs 240 tiles before waste, and 264 tiles with a 10 percent waste allowance.
How much extra tile should I buy for a backsplash?
About 10% for a straight layout, 12% for a brick pattern, 15% for diagonal and 20% for herringbone. Buy all of it at the same time, from the same batch — a later reorder may not match.
What is the standard backsplash height?
The standard height is 18 inches, from the counter to the bottom of the wall cabinets. Every linear foot of counter at 18 inches high is 1.5 square feet of backsplash.
How many boxes of backsplash tile do I need?
Divide the tile count by the tiles per box and round up. A 20 foot wall at 18 inches high needs 264 subway tiles with 10% waste, or 7 boxes at 40 tiles per box.
How much grout do I need for a backsplash?
About 1 lb of unsanded grout per 5 sq ft for subway tile, in 25 lb bags. A 30 sq ft backsplash needs about 6 lb, or 1 bag. Larger tiles with wider joints use more.
Do I deduct outlets from the backsplash area?
Yes — deduct about half a square foot per outlet or switch you have to cut around. A wall with many outlets needs the deduction and the higher waste allowance, since every cut consumes tile.
Should I buy an extra box of backsplash tile?
Yes. Always order a full extra box as a spare — tiles from the same dye lot can be impossible to match later for repairs, and a single chipped tile is the most common reason to need one.