SwiftTools

Deck Stain Calculator

A 16 by 12 foot deck with 40 feet of railing and 4 steps needs 2.62 gallons of semi-transparent stain for two coats — buy 3 one-gallon cans. Enter your deck below for the exact gallons, cans and cost.

Your deck
area = floor + railing × surface per ft + steps × width × 1.5625 · gallons = area ÷ first-coat coverage + (coats − 1) × area ÷ later-coat coverage, × (1 + extra) · later coats spread 1.5–2× as far

Coverage is the figure on the can you buy, and the can prints a range because wood varies: use the low end on rough or weathered boards. The defaults are BEHR PREMIUM's published pair for semi-transparent stain — 250 sq ft per gallon on the first coat, 500 on the second — and the same 2× step for solid colour; transparent toner starts at 300 then 600. A later coat always spreads further than the first, because the first coat has already filled the pores: published figures put it at 1.5 to 2 times as far. Change either rate to match your can — the can governs.

Stain only, deck only. Paint covers differently (rough-sawn paint runs about 250 sq ft per gallon, smooth about 350) — use the Fence Paint Calculator or the Paint Calculator for paint. Fences take stain too, but at fence rates — see the Deck Refinishing Cost Calculator if you are pricing the whole job, not just the stain. Estimates only — read your can: a test board on your own wood beats any default.

How the deck stain calculator works

A deck is more than its floor, and the stain math has to count all of it. The total area is the floor plus the railings plus the stairs: floor is length times width, railings are railing length times the surface per foot — 4.5 square feet per foot for a typical baluster railing — and each step is its width times 1.5625 square feet, the tread plus the riser. On the default deck — 16 by 12 ft, 40 ft of railing, 4 steps 4 ft wide — that is 192 + 180 + 25 = 397 square feet. Railings and stairs add about as much area as the floor itself, which is why floor-only estimates always come up short.

The coats do not cover the same area per gallon. The first coat soaks into bare, thirsty wood and covers about 250 square feet per gallon for semi-transparent stain; the second coat lands on partly sealed wood and covers about 500. Gallons equals area divided by the first-coat coverage, plus area divided by the later-coat coverage for each extra coat, times one plus the extra allowance. On the default deck that is 397 / 250 = 1.59 gallons first coat, 397 / 500 = 0.79 second, 2.38 total, and with 10% extra 2.62 gallons — buy 3 one-gallon cans, or one 5-gallon pail if it costs less per gallon.

Wood condition moves the answer as much as the stain type does. Weathered, grey wood drinks about 20% more than new wood, and rough-sawn or very porous wood about 38% more — the calculator divides the coverage by 0.8 and 0.62 for those conditions. The same default deck on rough, weathered boards needs 4.23 gallons instead of 2.62. The published ranges make the same point: a gallon covers 150 to 300 square feet on the first coat depending on the product and the wood, and the can you buy prints its own range — use the low end if your boards are old.

Worked example at the floor-only scale: a 16 by 12 ft deck floor alone, 192 square feet, two coats at 250 sq ft per gallon, plus 10%, is 192 / 250 x 2 x 1.10 = 1.69 gallons, so buy 2 gallons. And a larger deck at the other end: a 16 by 20 ft floor (320 sq ft) with 40 ft of railing (about 227 sq ft) is 547 square feet; at 250 first coat and 375 second — the 1.5-times step some makers publish — that is 2.19 + 1.46 = 3.65, plus 10% is 4.01 gallons, so buy 5 one-gallon cans or a 5-gallon pail. The 1.5-times and 2-times second-coat steps bracket the same job within a can of each other.

Common mistakes: measuring the floor only and forgetting the railings, which on many decks are half the area again; using one flat coverage rate for both coats, which overstates a two-coat job by a third; and staining wood that is still wet or dirty — stain on a damp deck peels, and stain over grey, weathered wood without cleaning first never takes evenly. Wash the deck, let it dry two to three days, and brush a test board first: the colour on your own wood is the only one that counts.

area = floor + railing x 4.5 sq ft/ft + steps x width x 1.5625 · gallons = area / first-coat coverage + (coats - 1) x area / later-coat coverage, x (1 + extra) · semi-transparent 250/500, transparent 300/600, solid 250/500 sq ft/gal · weathered / 0.8, rough / 0.62

Related tools

Price the whole refinishing job with the Deck Refinishing Cost Calculator, count the boards with the Deck Material List Calculator, and the screws with the Deck Screws Calculator. For paint instead of stain, use the Fence Paint Calculator or the Paint Calculator.

Deck stain calculator FAQ

How much stain do I need for a deck?

Add the floor, railings and stairs, then divide by the coverage per coat. A 16 by 12 ft deck with 40 ft of railing and 4 steps is 397 sq ft; at 250 sq ft/gal first coat and 500 second, that is 1.59 + 0.79 = 2.38 gallons, or 2.62 with 10% extra — buy 3 gallons.

How many square feet does a gallon of deck stain cover?

About 250 sq ft per gallon on the first coat for semi-transparent stain, 300 for transparent toner, and 200 to 400 for solid colour. The second coat covers roughly 1.5 to 2 times as far — 500 sq ft/gal for semi-transparent — because the first coat has sealed the pores.

Do railings really need that much stain?

Yes — a typical baluster railing is about 4.5 square feet of surface per linear foot, so 40 ft of railing is 180 sq ft, nearly as much as a 16 by 12 ft floor. On many decks the railings and stairs add 50 to 100% to the floor area.

How many coats of deck stain do I need?

Two coats on bare or stripped wood, one coat for a maintenance refresh on previously stained wood in good condition. A third coat adds little protection and can leave a sticky film — two coats is the standard.

Does weathered wood need more stain?

Yes — weathered, grey wood drinks about 20% more than new wood, and rough-sawn or very porous wood about 38% more. The calculator applies those factors to the coverage rate. Use the low end of the can's printed range on old boards.

How long should I wait after washing before staining?

Two to three dry days after washing or power-washing. Stain on damp wood peels, and stain over grey, weathered wood that was never cleaned never takes evenly. Brush a test board first to check the colour on your own wood.

Should I buy gallons or a 5-gallon pail?

Whichever costs less per gallon — a pail is usually cheaper per gallon, but only if you will use it. Unopened cans can often be returned, so buying one extra gallon as insurance is cheaper than a second trip to the store.