SwiftTools

Shed Height Calculator

Enter your low wall height, building width and roof pitch, and this shed height calculator returns the roof rise, total building height, roof angle and rafter length — the numbers that decide whether a shed fits under a height limit.

Your shed dimensions
rise = run x pitch / 12 · total height = low wall height + rise · angle = arctan(pitch / 12) · rafter length = sqrt(run^2 + rise^2)

Height is measured from grade to the top of the roof at the high wall, before roof assembly thickness, ridge cap and foundation height — add those where your local rule counts them. Asphalt shingles need a minimum slope of 2:12, with special low-slope underlayment from 2:12 to 4:12. Many jurisdictions cap accessory-building height (commonly around 12 to 15 feet) and require setbacks; this is a planning estimate, not a permit approval or structural design, and rafter sizing for snow and wind loads needs local code tables.

How the shed height calculator works

A single-slope (shed or lean-to) roof gains height across its full width: rise equals run times pitch divided by 12, because pitch is inches of rise per 12 inches of run. Total shed height is the low wall height plus that rise. Roof angle is arctan(pitch / 12), and rafter length is the hypotenuse of run and rise — extended past the wall by the eave overhang divided by the cosine of the angle. A steeper pitch sheds rain and light snow faster but raises the high wall, the rafter length, wind exposure and sometimes the permit question.

Worked example: an 8-foot low wall, 10-foot building width and 4:12 pitch gives a rise of 10 x 4 / 12 = 3.33 feet (40 inches), a total height of 8 + 3.33 = 11.33 feet, an angle of 18.43 degrees, a rafter length of sqrt(120^2 + 40^2) = 126.49 inches (10.54 feet), and 139.14 inches (11.59 feet) with a 12-inch overhang. A 12-foot-wide lean-to at 3:12 with an 8-foot low wall rises 12 x 3 / 12 = 3 feet for an 11-foot total; an 8-foot run at 6:12 with a 7-foot low wall rises 4 feet for an 11-foot total.

Common mistakes: using half the width as the run (that is a gable roof — a shed roof uses the full width), forgetting the overhang in the rafter length, and measuring height to the low wall instead of the high side (height limits are measured to the highest point). Asphalt shingles need at least a 2:12 slope, with special low-slope underlayment from 2:12 to 4:12 — below 2:12 use a membrane or metal system rated for low slopes. The Shed Roof Pitch Calculator converts pitch, angle and slope; the Shed Cost Calculator prices the whole building.

rise (ft) = run (ft) x pitch / 12 · total height = low wall height + rise · angle = arctan(pitch / 12) · rafter length = sqrt(run^2 + rise^2), plus overhang / cos(angle) with eaves

Related tools

Also try the Shed Roof Pitch Calculator for pitch conversions, the Shed Cost Calculator for the building budget, and the Lean-To Roof Pitch Calculator for attached lean-to roofs.

Shed height calculator FAQ

How do I calculate total shed height?

Add the roof rise to the low wall height. Rise is building width times pitch divided by 12: a 10-foot width at 4:12 rises 3.33 feet, so an 8-foot low wall gives an 11.33-foot total height.

What is the roof angle for a 4:12 pitch?

About 18.43 degrees (arctan(4/12)). For reference: 2:12 is 9.46 degrees, 3:12 is 14.04 degrees, 5:12 is 22.62 degrees and 6:12 is 26.57 degrees.

What is the minimum roof pitch for a shed?

For asphalt shingles, 2:12, with special low-slope underlayment required from 2:12 to 4:12. Below 2:12, use a roofing system rated for low slopes, such as a membrane or standing-seam metal.

Does the overhang change the rafter length?

Yes — the rafter must extend past the wall by the overhang measured along the slope. A 12-inch overhang on a 4:12 roof extends the 126.49-inch rafter to 139.14 inches.

Why does pitch change the wall height difference?

Because the rise spans the full building width on a shed roof: at 4:12, every foot of width adds 4 inches of height difference between the low and high walls. A 12-foot lean-to at 3:12 differs by 36 inches wall to wall.

Will my shed pass a height limit?

Compare the total height here against your local accessory-building limit, commonly around 12 to 15 feet — but check how your jurisdiction measures height (grade point, roof assembly, foundation) and what setbacks apply. This calculator does not grant approval.

Does this size the rafters?

No — it gives rafter length only. Rafter size (2x6, 2x8, 2x10 or engineered) depends on span, spacing, snow and wind loads and local code tables, so confirm sizing before ordering lumber.