SwiftTools

Paver Sand Calculator

Enter your patio size and joint width, and this paver sand calculator returns the bedding sand — cubic yards, tons or bags — plus the polymeric joint sand and the cost, using the 1-inch bedding layer the ICPI standard calls for.

Your patio
bedding sand (cu yd) = area x 1.2 in / 12 / 27 · order = bedding x 1.10 · tons = cu yd x 1.35 · 50-lb bags = cu ft / 0.5 · polymeric bags = ceil(area / coverage per bag)

Bedding sand is a 1-inch screeded layer of ASTM C33 concrete sand per ICPI Tech Spec 2 — never thicker, and never mason or play sand, which are too fine and hold water. Spread 1.2 inches loose and compact to 1 inch finished. Sweep polymeric sand into dry joints on a dry day, then water it to set. This is a planning estimate; the 4 to 8 inch crusher-run base under the sand is not included.

How the paver sand calculator works

Paver sand is two different products. Bedding sand is the 1-inch layer of washed concrete sand screeded flat over the compacted gravel base — ICPI Tech Spec 2 calls for exactly 1 inch finished, so you spread 1.2 inches loose and compact it down. The volume is area times 1.2 inches, converted to cubic yards, plus 10% for spillage and uneven screed. One cubic yard of concrete sand weighs about 1.35 tons, and a 50-pound bag holds about half a cubic foot, so a yard is roughly 54 bags.

Worked example: a 20 by 10 foot patio is 200 square feet. Bedding sand is 200 times 1.2 divided by 12, or 20 cubic feet — 0.74 cubic yards loose, 0.81 to order with 10% extra, about 1.10 tons or 44 bags of 50 pounds. Polymeric joint sand at 1/8-inch joints covers about 90 square feet per 50-pound bag, so 200 divided by 90 rounds up to 3 bags. At $45 a cubic yard and $20 a bag, the sand costs about $97.

Common mistakes: laying a 2 or 3 inch sand bed to make up for an uneven base — sand behaves like a fluid under load, so a thick bed migrates and the pavers sink in the traffic pattern; using mason sand or play sand, which are too fine, hold water and pump out of the joints; and sweeping polymeric sand into wet joints or before compacting, which stops it setting properly. This calculator covers sand only — the 4 to 8 inches of crusher-run base underneath, the pavers and the edge restraint are separate. The Paver Calculator sizes the full materials list.

bedding sand (cu yd) = area x 1.2 in / 12 / 27 · order = bedding x 1.10 · tons = cu yd x 1.35 · 50-lb bags = cu ft / 0.5 · polymeric bags = ceil(area / coverage per bag)

Related tools

Also try the Paver Calculator for the full materials list, the Sand Calculator for general sand volumes, and the Gravel Calculator for the base underneath.

Paver sand calculator FAQ

How much sand do I need under pavers?

Exactly 1 inch screeded flat. A 200 sq ft patio needs 0.74 cubic yards loose (1.2 inches spread), or 0.81 cubic yards to order with 10% extra — about 1.10 tons, or 44 bags of 50 pounds.

How much polymeric sand do I need?

One 50-pound bag covers about 90 sq ft at 1/8-inch joints, 70 sq ft at 1/4 inch, 48 sq ft at 3/8 inch, and only about 25 sq ft on flagstone with wide joints. Divide your patio area by the coverage rate and round up.

What kind of sand goes under pavers?

ASTM C33 concrete sand — coarse, washed, sharp-edged grains that lock together and drain. It is sold as bedding sand or all-purpose sand. Do not use mason sand or play sand under pavers.

Can I use mason sand under pavers?

No. Mason sand (ASTM C144) is washed fine sand for mortar; under pavers it holds water, stays soft and pumps out of the joints. Concrete sand is the only bedding sand the ICPI standard allows.

How thick should sand be under pavers?

One inch screeded, from 1.2 inches loose that compacts down. Thicker beds sink: sand migrates sideways under wheel and foot loads, and the pavers above it settle in exactly the pattern of the traffic.

How many bags of sand equal a cubic yard?

About 54 bags of 50 pounds per cubic yard — a yard is 27 cubic feet and each bag holds about half a cubic foot. For anything over about 100 sq ft, bulk sand delivered is far cheaper than bags.

Do I need polymeric sand or regular sand in paver joints?

Polymeric sand is graded sand with a binder that hardens when watered, locking the joints and keeping weeds and ants out. Regular joint sand washes out faster and needs topping up; use polymeric unless the paver manufacturer says otherwise.