SwiftTools

Deck Boards Calculator

Enter your deck size, board width and gap, and this deck boards calculator returns the rows, linear feet, boards to buy, screws and cost — with the waste allowance a real deck job needs.

Your deck
pitch = face width + gap · rows = ceil(deck width in inches / pitch) · linear feet = rows x deck length · boards = ceil(linear feet x (1 + waste%) / board length) · joists = floor(deck length in inches / spacing) + 1 · screws = rows x joists x 2

A 5/4 x 6 deck board is 5.5 inches wide, not 6 — use the actual face width or the count comes out short. Gap: 1/8 inch for composite or dry lumber, 1/4 inch for dry pressure-treated; wet pressure-treated goes down nearly tight and shrinks to its gap. Waste: 10% for a straight layout, 15% diagonal, 20% herringbone. This is a planning estimate; check your board manufacturer's spacing guide before ordering.

How the deck boards calculator works

Deck boards are sold by the piece but they cover by the row, so the whole estimate hangs on one number: how much width one board plus its gap covers. That pitch is the board face width plus the gap — 5.5 inches plus a 1/4 inch gap is 5.75 inches. Divide the deck width in inches by the pitch and round up for the row count; multiply rows by the deck length for linear feet; then add waste and divide by the board length, rounding up to whole boards.

Worked example: a 12 by 16 foot deck with 5.5-inch boards and a 1/4-inch gap needs 144 divided by 5.75, rounded up to 26 rows. That is 26 times 16, or 416 linear feet. With 10% waste that is 457.6 linear feet, or 29 boards of 16 feet. At 16-inch joist spacing there are 13 joists and 338 joist crossings, so 676 screws at two per crossing — and about $290 at $10 a board.

Common mistakes: using the nominal 6 inches instead of the actual 5.5-inch face, which undercounts the job by about 9%; forgetting the gap, which leaves the last board short of the edge; skipping the waste allowance, so cut ends and one bad board send you back to the yard; and lining up all the butt joints on one joist — stagger them across joists for a stronger, better-looking deck. The Deck Joist Span Calculator sizes the framing underneath, and the Deck Board Staggering Calculator plans the joint pattern.

pitch = face width + gap · rows = ceil(deck width in inches / pitch) · linear feet = rows x deck length · boards = ceil(linear feet x (1 + waste%) / board length) · screws = rows x joists x 2

Related tools

Also try the Deck Joist Span Calculator for the framing, the Deck Board Staggering Calculator for joint layout, and the Deck Post Spacing Calculator for posts.

Deck boards calculator FAQ

How many deck boards do I need for a 12x16 deck?

With 5.5-inch boards and a 1/4-inch gap: 26 rows, 416 linear feet, and 29 boards of 16 feet once you add 10% waste. Diagonal layouts need 15% waste instead, or about 30 boards.

How many linear feet of decking per square foot?

About 2.2 linear feet per square foot for 5.5-inch boards at a 1/4-inch gap — 209 linear feet per 100 square feet. Wider boards and wider gaps lower that number; narrower boards raise it.

What gap should I leave between deck boards?

About 1/8 inch for composite decking and dry lumber, 1/4 inch for dry pressure-treated lumber. Wet pressure-treated boards go down nearly tight and shrink to their gap as they dry.

How many screws do I need for decking?

Two screws per joist crossing. A 12 by 16 foot deck at 16-inch joist spacing has 338 crossings, so 676 screws — buy a box of 700 and keep the spares. Hidden fasteners replace screws one-for-one per crossing.

Should I add waste when ordering deck boards?

Yes: 10% for a straight perpendicular layout, 15% for diagonal, 20% for herringbone. Waste covers cut ends, butt joints, a warped board or two, and future repairs.

What is the actual width of a 6-inch deck board?

5.5 inches. A 5/4 by 6 board is 1 inch thick and 5.5 inches wide once milled — the 6-inch figure is the nominal size before surfacing. Always use the actual face width in the math.

How long should deck boards be?

Match or exceed the deck length where you can: 16-foot boards for a 16-foot run avoid butt joints entirely. Shorter boards are fine if every butt joint lands on a joist and joints are staggered across the deck.