SwiftTools

Roll & Batt Insulation Calculator

Enter the area to insulate and the coverage printed on the pack, and this roll and batt insulation calculator returns the packs to buy — and the depth your target R-value needs.

Your insulation
packs = ceil(area x (1 + waste%) / coverage per pack) · depth = target R / R-value per inch (fiberglass 3.2, mineral wool 4.0)

Rolls and batts only — pre-cut batts and continuous rolls. For loose-fill blown-in bags, use the Blown-In Insulation Calculator. Coverage per pack varies enormously by R-value and brand — a higher-R, thicker pack covers noticeably less square footage — so always use the figure printed on your package label: common values are 88.75 sq ft per bag of R-13 fiberglass batts, about 49 sq ft per R-19 roll, and about 32 sq ft per bag of mineral wool batts.

How the roll & batt insulation calculator works

Insulation is sold by coverage, not by the roll or batt: every pack prints the square footage it covers at its R-value, and that number is what the calculator divides by. Measure the area, add a waste allowance for cutting around joists, wiring and odd corners — 10% is the common starting point, 15% or more for cut-up areas — divide by your pack coverage and round up to whole packs, because a store will not sell you part of one. The depth follows from the R-value: divide the target R by the R-value per inch of the material — about 3.2 per inch for fiberglass, about 4.0 for mineral wool — so R-49 in fiberglass needs about 15.3 inches and in mineral wool about 12.3.

Worked example: a 500-square-foot area with rolls covering 100 square feet each and 10% waste needs 550 divided by 100, or 5.5 — 6 packs. A 1,000-square-foot attic at the same coverage takes 11 packs. With R-13 fiberglass batts at 88.75 square feet per bag, 1,320 square feet takes 1,320 divided by 88.75, or 14.87 — 15 packs before waste. The same area in mineral wool batts at about 32 square feet per bag takes far more packs — the bags are smaller, so compare cost per square foot, not pack count.

Common mistakes: using one universal coverage figure (a higher-R, thicker pack covers noticeably less per package than a thinner one, even in the same brand); measuring the floor area for walls (walls are perimeter times height, minus doors and windows — insulation does not cover glass); and confusing rolls and batts with blown-in (loose-fill is counted in bags off a manufacturer chart, on the Blown-In Insulation Calculator, not by pack coverage). Energy Star attic targets are roughly R-30 in hot Zone 1, R-49 across most of the country and R-60 in the coldest zones; walls are typically R-13 to R-21 depending on climate and cavity depth. The Insulation Cost Calculator prices the whole installed job.

packs = ceil(area x (1 + waste%) / coverage per pack) · depth = target R / R-value per inch · fiberglass 3.2 R/in, mineral wool 4.0 R/in · waste: 10% simple, 15%+ cut-up areas

Related tools

Also try the Blown-In Insulation Calculator for loose-fill bags, the Insulation Cost Calculator for the installed price, and the Spray Foam Insulation Cost Calculator for the foam alternative.

Roll & batt insulation calculator FAQ

How many rolls of insulation do I need for 500 sq ft?

Divide the area by the coverage per roll and add 10% waste: 500 square feet at 100 square feet per roll is 550 divided by 100, or 5.5 — 6 rolls. With R-13 batts at 88.75 square feet per bag it is 7 bags.

How much coverage is in a roll of insulation?

It varies enormously by R-value and brand: about 88.75 square feet per bag of R-13 fiberglass batts, about 49 square feet per R-19 roll, and about 32 square feet per bag of mineral wool batts. Always check the label on your product.

What is the R-value per inch of fiberglass and mineral wool?

About 3.2 per inch for fiberglass batts and rolls, and about 4.0 per inch for mineral wool. So R-49 needs about 15.3 inches of fiberglass or about 12.3 inches of mineral wool.

How deep should attic insulation be for R-49?

About 15.3 inches of fiberglass batts or rolls, or about 12.3 inches of mineral wool. The calculator gives the depth for your target R and material; measure it after install, not from the bag count.

What is the difference between batts and rolls?

Batts are pre-cut to fit standard stud and joist bays (15 or 23 inches wide); rolls are the same material in a continuous length you cut to fit. The math is identical — both are counted by pack coverage — but rolls waste less on long runs.

Should I use batts or blown-in insulation?

Batts suit open, accessible cavities with standard spacing; blown-in suits attics with obstructions, irregular joists and hard-to-reach corners, where it fills around everything. The Blown-In Insulation Calculator counts bags for that job.

How much waste should I add for insulation?

10% is the common starting point for a straightforward rectangular space; use 15% or more for cut-up areas with many joists, wiring, pipes and odd corners. Round up to whole packs either way.