Self-Leveling Concrete Calculator
A 12 by 10 foot floor at an average 1/4 inch needs 7 bags of self-leveler — 2.75 cubic feet with the usual 10% allowance. Enter your floor size and depth below for the exact bags, water and cost.
The yield is the figure on the bag you buy: QUIKRETE's self-leveling resurfacer yields 0.45 cubic feet per 50 lb bag (about 21.6 sq ft at 1/4 in), LevelQuik RS about 0.49, SikaLevel about 0.44, ARDEX K 22 F about 0.52. Some bags print a coverage instead of a yield — work the yield out as coverage in sq ft times depth in inches divided by 12. Sakrete's bag, for example, covers about 27.5 sq ft at 1/4 in, which is about 0.57 cu ft a bag: pick Custom and type 0.57. The average depth is the average gap between the finished height and the floor — measure the highs and lows with a long straightedge or a laser, and never use the deepest spot for the whole floor.
Thin underlayment only. This page sizes self-leveling underlayment for floors before tile, vinyl or carpet — not a structural slab, which takes ready-mix or bagged concrete mix instead. Each product has its own depth range in one pour without added aggregate (LevelQuik RS featheredge to 1.5 in, SikaLevel 1/8 in to 2 in, ARDEX K 22 F 1/8 in to 1 1/4 in) — deeper than that, use aggregate-extended mix or regular concrete. Planning estimate, not a substitute for professional approval: primer, substrate condition and curing all come from the product data sheet, not this page.
How the self-leveling concrete calculator works
Self-leveler is sold by the bag but needed by volume, so the work is one multiplication and one division. Volume is the floor area times the average depth in feet: a 12 by 10 ft floor is 120 square feet, and at an average 1/4 inch that is 120 x 0.25 / 12 = 2.5 cubic feet. Add the 10% allowance for what stays in the bucket and the low spots you did not find — 2.75 cubic feet — then divide by the yield of one bag and round up. At QUIKRETE's 0.45 cubic feet per 50 lb bag that is 2.75 / 0.45 = 6.11, so buy 7 bags.
The yield is the number that moves the answer, and it varies by product. QUIKRETE yields 0.45 cubic feet per bag, LevelQuik RS about 0.49 (23.5 sq ft at 1/4 in), SikaLevel about 0.44 (21 sq ft at 1/4 in), ARDEX K 22 F about 0.52 (50 sq ft at 1/8 in). The same 120 sq ft floor at 1/4 in takes 7 bags of QUIKRETE, 6 of LevelQuik, 7 of SikaLevel and 6 of ARDEX — the product choice moves the count by a bag either way, so pick your product first and type its yield if it is not listed. Coverage halves each time the depth doubles: one bag covers about 43 sq ft at 1/8 in, 22 at 1/4 in, 11 at 1/2 in and 5.4 at 1 in.
The average depth is the part most people get wrong. Measure the floor's highs and lows with a long straightedge or a laser and settle the finished height: the average depth is the average gap between that height and the floor. Never use the deepest spot for the whole floor — a 1/2 in dip in one corner does not mean the whole room needs 1/2 in. For a dip in an otherwise level floor, measure it as an area of its own: a 150 sq ft room at 1/4 in plus a 50 sq ft low area at 1/2 in is a weighted average of 0.3125 in, not 1/2 in.
Worked example at a larger scale: a 200 square foot floor at 1/4 inch is 200 x 0.25 / 12 = 4.167 cubic feet, 4.583 with the 10% allowance, and at 0.45 cubic feet per bag that is 10.19, so buy 11 bags — $385 at $35 a bag. The mixing water follows the bags: LevelQuik RS takes 5.25 to 5.75 quarts per bag, SikaLevel 1 gallon per bag, so the 200 sq ft example needs about 58 to 63 quarts with LevelQuik or 44 quarts with SikaLevel. Measure the water — too much water weakens the pour and too little stops it flowing.
Common mistakes: using the deepest spot as the average depth, which can double the order; skipping the primer, which lets the subfloor drink the water out of the mix and leaves a weak bond; and pouring deeper than the product allows in one lift — LevelQuik RS tops out at 1.5 in, SikaLevel at 2 in, ARDEX K 22 F at 1 1/4 in without aggregate. Past that, use an aggregate-extended mix or regular concrete. Self-leveler is walkable within hours, but the floor going on top sets the real wait: tile after 4 hours, vinyl and carpet after 16 hours to a day, wood after 16 hours to 3 days, depending on the product.
volume = area x average depth / 12 · bags = ceil(volume x (1 + waste) / yield per bag) · QUIKRETE 0.45, LevelQuik RS 0.49, SikaLevel 0.44, ARDEX K 22 F 0.52 cu ft per 50 lb bag · coverage per bag halves as depth doubles
Related tools
Pouring a new slab instead? Use the Concrete Slab Calculator for the volume and the Concrete Bags Calculator for the bag count. Seal the finished floor with the Concrete Sealer Calculator, and keep a fresh slab damp while it cures with the Concrete Curing Water Calculator.
Self-leveling concrete calculator FAQ
How many bags of self-leveling concrete do I need?
Multiply the floor area by the average depth in feet, add 10% waste, and divide by the yield of one bag. A 12 by 10 ft floor at 1/4 in is 2.5 cu ft, 2.75 with waste, and at 0.45 cu ft per bag that is 6.11 — buy 7 bags.
How far does one bag of self-leveling concrete go?
It depends on the depth: one 50 lb bag covers about 43 sq ft at 1/8 in, 22 sq ft at 1/4 in, 11 sq ft at 1/2 in and 5.4 sq ft at 1 in (QUIKRETE yield, 0.45 cu ft). Coverage halves each time the depth doubles.
What is the average depth — the deepest spot?
No — the average gap between the finished height and the floor. Measure the highs and lows with a long straightedge or a laser and average them. Using the deepest spot for the whole floor can double the order. A dip in an otherwise level floor should be measured as an area of its own.
How much water does self-leveling concrete need?
LevelQuik RS takes 5.25 to 5.75 quarts per 50 lb bag, SikaLevel 1 gallon per bag. Measure it — too much water weakens the pour and too little stops it flowing. The calculator adds the water up for the bags it counts.
Do I need primer before self-leveling concrete?
Yes — primer stops the subfloor drinking the water out of the mix, which would leave a weak bond. It is not counted as bags here: add it separately at the coverage printed on the primer, usually around 200 to 300 sq ft per gallon.
How thick can I pour self-leveling concrete?
Each product has its own range in one pour without added aggregate: LevelQuik RS from featheredge to 1.5 in, SikaLevel 1/8 in to 2 in, ARDEX K 22 F 1/8 in to 1 1/4 in. Deeper than that, use an aggregate-extended mix or regular concrete.
How long before I can walk on self-leveling concrete?
Walkable within hours — LevelQuik RS in 2 to 4 hours, SikaLevel in 2 to 3. The floor going on top sets the real wait: tile after 4 hours, vinyl and carpet after 16 hours to a day, wood after 16 hours to 3 days, depending on the product.