Crown Molding Calculator
Enter your room size, and this crown molding calculator returns the linear feet, how many stock pieces to buy, the finish nails, the cost — and the exact miter and bevel settings for your crown's spring angle and corner.
Saw settings come from the standard compound-angle geometry, matching the Starrett crown molding charts: a 38° spring crown in a square 90° corner cuts at 31.62° miter and 33.86° bevel, and a 45° spring crown at 35.26° miter and 30.00° bevel. Those figures are for crown cut flat, back on the saw table. Waste of 10 to 15% covers miter off-cuts and coping mistakes, plus one spare piece for a first job. Always cut a scrap test corner first — a wall that reads square is often 89° or 91° where it matters. This is a planning estimate.
How the crown molding calculator works
Crown molding follows the top edge of every wall, so the amount you need follows the room perimeter, not its floor area: 2 times (length + width), plus any extra runs over soffits or beams. Add 10% for the angled off-cuts at inside and outside corners, the short returns over doors and windows, and the occasional mis-cut, then divide by the stock piece length — 8, 12 or 16 feet — and round up, because lumber yards sell molding by the full length, not by the inch. A 16 foot piece spans most walls without a scarf joint, which is why it is the default.
Worked example: a 12 by 14 foot room has a 52 foot perimeter, which is 57.2 feet of crown molding with 10% waste, or 4 pieces of 16 feet. A 16 by 20 foot living room with a 5 foot soffit run is 77 feet of perimeter, 88.55 feet with 15% waste — buy 8 pieces of 12 feet, or 96 feet of molding. At $3.50 per foot the 12 by 14 room costs 4 x 16 x $3.50 = $224. Nails run about 2 per nailing point on studs 16 inches on center: the 52 foot room takes 39 points, or 78 finish nails.
Common mistakes: measuring the floor area instead of the perimeter, forgetting the soffit and beam runs, and buying exactly the perimeter with no waste — the first mitered corner alone eats a foot of molding. The saw settings are the other half of the job: crown is cut flat on the table, face up, with both saw scales moved. A 38° spring crown in a square 90° corner cuts at 31.62° miter and 33.86° bevel; a 45° spring crown at 35.26° miter and 30.00° bevel. Measure out-of-square corners with an angle finder — the corners of a 135° bay are entered as 135 — and always cut a scrap test corner first. The Shiplap Calculator and Board and Batten Calculator size the other wall treatments in the same room.
perimeter = 2 x (length + width) + extra runs · order length = perimeter x 1.10 · pieces = ceil(order length / piece length) · 38° spring, 90° corner: miter 31.62°, bevel 33.86° · 45° spring, 90° corner: miter 35.26°, bevel 30.00° · nails = ceil(perimeter x 12 / 16) x 2
Related tools
Also try the Shiplap Calculator for shiplap walls, the Board and Batten Calculator for batten cladding, and the Wallpaper Calculator for papered walls.
Crown molding calculator FAQ
How much crown molding do I need for a 12x14 room?
A 12 by 14 foot room has a 52 foot perimeter, which is 57.2 feet of crown molding with 10% waste — buy 4 pieces of 16 feet. A 16 by 20 foot room with a 5 foot soffit run needs 88.55 feet with 15% waste, or 8 pieces of 12 feet.
What are the miter and bevel angles for crown molding?
For 38° spring crown in a square 90° corner: 31.62° miter and 33.86° bevel. For 45° spring crown: 35.26° miter and 30.00° bevel. Those are the settings printed on most saw tables, for crown cut flat on the table.
What is the spring angle of crown molding?
The angle between the back of the molding and the wall. The two common profiles are 52/38 crown with a 38° spring (52° against the ceiling) and 45/45 crown with a 45° spring. Measure it by sitting an offcut in the corner and reading the angle off the wall.
How much waste should I allow for crown molding?
Ten to 15% for the miter off-cuts, plus one spare piece for a first job. First-timers should use 15%: coping mistakes and mis-cut miters are the usual reason for a second trip to the store.
How many nails do I need for crown molding?
About 2 finish nails per nailing point, with points every 16 inches on studs. A 52 foot room has 39 nailing points, or 78 nails; a 77 foot room has 58 points, or 116 nails.
What length does crown molding come in?
Crown molding is sold in 8, 12 and 16 foot lengths. A 16 foot piece spans most walls without a scarf joint, so it is the usual buy for rooms over 12 feet — but it needs a clear path and a second pair of hands to carry.
Should crown molding be cut flat or nested?
Either works. Cut flat on the table to use the miter and bevel pair from this calculator — the molding lies face up and both saw scales move. Cut nested (upside down against the fence, held at its spring angle) to use a simple miter with the bevel at zero. Flat is easier to set up; nested is faster once the stop is set.