Shiplap Calculator
Enter your wall size and board profile, and this shiplap calculator returns the rows, the boards to buy, the linear feet and the cost — for a wall or a ceiling, with the exposed face that actually drives the count.
Exposed faces are the typical figures for common profiles: UFP-Edge 1 x 6 shiplap is 5 3/8 in wide with a 4 5/8 in exposed face, and UFP-Edge Timeless 1 x 8 nickel-gap pine has a 6 7/16 in exposed face. Other makers and profiles differ — measure your boards and use the custom face if yours is different. Waste of 10% suits a plain wall; use 15% for a wall with openings or a ceiling, where off-cuts are less likely to fit elsewhere. This is a planning estimate; check your board label for the exact face.
How the shiplap calculator works
Shiplap is counted in two directions. Rows are the wall height divided by the exposed face — the width a board covers once lapped, not its width — rounded up, since that is how many horizontal courses it takes to climb from floor to ceiling. Boards per row are the wall length divided by the stock board length, rounded up. Multiply the two for the net board count, then add waste: 10% for a plain wall, 15% for a wall with openings or a ceiling, where off-cuts are less likely to fit elsewhere. Openings come off the area first — a standard door is 21 sq ft and a standard window 12 sq ft.
Worked example: a 12 foot wide, 8 foot tall wall covered with horizontal 1 x 6 shiplap with a typical 4 5/8 in exposed face. Rows are 96 / 4.625 = 20.76, rounded up to 21. Each row is 12 feet long, so it takes an 8 foot board plus a 4 foot piece — 32 boards before waste, with the off-cuts shared between rows. With 10% waste that is 36 boards, or 288 linear feet, covering about 111 sq ft for 96 sq ft of wall — about $288 at $8 a board. The same wall in 1 x 8 nickel-gap pine (6 7/16 in face) needs only 15 rows and about 26 boards.
Common mistakes: using the board width instead of the exposed face (a 1 x 6 is 5 3/8 in wide but only covers 4 5/8 in once lapped — counting by width leaves you a row short), buying exactly the net count (every row ends in a cut, and some cuts are too short to reuse), and forgetting that vertical shiplap swaps the axes — columns across the width replace rows, and boards per column come from dividing height by stock length. Solid wood shiplap runs about $1.50 to $7 per square foot of material, depending on species and grade. The Board and Batten Calculator sizes the other classic wall cladding, and the Wallpaper Calculator covers the wall if you paper instead.
rows = ceil(wall height in inches / exposed face in inches) · boards per row = ceil(wall length / board length) · boards = ceil(rows x boards per row x (1 + waste%)) · 1 x 6 face = 4 5/8 in, 1 x 8 nickel-gap face = 6 7/16 in · waste: 10% plain wall, 15% with openings or ceiling
Related tools
Also try the Board and Batten Calculator for batten cladding, the Wallpaper Calculator for paper, and the Drywall Needed Calculator for the wall underneath.
Shiplap calculator FAQ
How many boards do I need for a 12x9 foot wall?
A 12 by 9 foot wall is 108 sq ft. With 1 x 6 shiplap (8-foot boards covering about 3.53 sq ft each with a standard gap), you need about 31 boards as a base count — buy 35 with 10% waste.
How do I calculate how much shiplap I need?
Multiply wall length by height, subtract openings, then divide height by the exposed face for the row count and length by stock board length for boards per row. Multiply those two and add waste. For a 14 by 9 wall with a 5.5-inch reveal and 12-foot stock, that is 40 boards, or 44 with 10% waste.
What is the exposed face of 1x6 shiplap?
About 4 5/8 inches for the common UFP-Edge profile — the board is 5 3/8 inches wide, and the lap hides about 3/4 inch. For 1 x 8 nickel-gap pine the exposed face is 6 7/16 inches. Measure your boards: other makers and profiles differ.
How much waste should I allow for shiplap?
Ten percent for a straightforward horizontal installation on a plain wall. Bump it to 15% if the wall has multiple windows and doors, since you cut around each corner and the off-cuts are less likely to fit elsewhere — and 12 to 15% for a ceiling.
Should shiplap run horizontal or vertical?
Horizontal is the classic look and the easiest install — boards span the wall in long runs. Vertical shiplap makes a room feel taller and suits entryways and wainscot-height runs, but every board is cut to wall height and the count swaps axes. Either way, the math is rows times boards per row.
How much does shiplap cost?
Solid wood shiplap ranges from about $1.50 to $7 per square foot of material, depending on species and grade. A 12 by 8 foot accent wall needs about 36 boards of 1 x 6 — roughly $288 at $8 a board — before trim and fasteners.
Can I install shiplap over drywall?
Yes — shiplap is usually nailed straight through drywall into the studs, with adhesive as a backup. Find the studs first: boards fastened only to drywall will pull loose. Leave a small expansion gap at the ends on long runs.