Roof Truss Cost Calculator
Prefab roof trusses cost about $60–$600 each in 2026 depending on span and type, and a typical 40 ft garage or home addition needs around 21 of them at 24-inch spacing. Enter your building length, spacing, span, and truss type for a full package estimate including installation.
Prices are 2026 U.S. ballparks for prefab wood trusses: a short-span common truss starts around $60–$120, while long spans, attic trusses, and heavy snow-load designs run $300–$600+. Your truss plant quotes exact figures from your plans — span, pitch, and load are engineered per building.
Estimates only — not an engineering quote. Trusses are designed and certified by the manufacturer for your exact loads; never substitute a generic design.
How the roof truss cost calculator works
Truss count comes from spacing: count = building length ÷ spacing + 1. A 40 ft building at the standard 24-inch (2 ft) spacing needs 40 ÷ 2 + 1 = 21 trusses — the +1 is the gable-end truss that beginners always forget. Sixteen-inch spacing, used under heavy snow or tile roofs, pushes the same building to 31.
Price per truss is driven mostly by span and type. The calculator steps the base price up as span grows (more lumber, bigger connector plates, more engineering), then applies a type multiplier: scissor trusses run about 35% more for the vaulted ceiling, attic trusses about 90% more because they are built like a floor and roof in one, and simple mono-pitch trusses about 20% less.
Installation is estimated at 30–40% of the truss cost when you include it — that covers the crane day and a framing crew to set, brace, and sheet. Delivery is usually quoted separately by the truss plant and rises with distance, so treat long-haul rural deliveries as an extra line item.
count = length ÷ spacing + 1 · package = count × unit price (span × type) · installed = package × 1.30–1.40
Related tools
Work the rest of the roof with the Roof Pitch Calculator, Roof Shingle Bundle Calculator, and the Roof Replacement Cost Calculator.
Roof truss cost calculator FAQ
How much does a roof truss cost?
About $60–$600 per truss in 2026. Short-span common trusses (up to about 24 ft) run $60–$150; mid spans of 30–40 ft run $150–$350; long spans, attic trusses, and heavy-load designs reach $400–$600+. Type matters as much as size — an attic truss costs roughly double a plain common truss of the same span.
How many trusses do I need for a 40 ft building?
At standard 24-inch spacing: 40 ÷ 2 + 1 = 21 trusses. At 16-inch spacing the same building needs 31. The extra +1 is the second gable end — a run always has one more truss than the number of spaces between them.
How much does it cost to install roof trusses?
Installation typically adds 30–40% of the truss package price. That covers a crane (often $500–$1,500 for the day) and a framing crew to set and brace the trusses. A 21-truss package at $3,500 usually lands around $4,600–$4,900 fully installed.
Are trusses cheaper than stick framing a roof?
Usually yes for standard shapes. Trusses use smaller lumber efficiently, arrive engineered and ready to set, and a crew can frame a roof in a day or two instead of a week of cutting rafters on site. Stick framing still wins for unusual shapes or where attic space must be fully open.
What span can a wood roof truss cover?
Standard prefab wood trusses commonly span 24–60 ft clear without interior support. Scissor and attic designs usually top out lower for the same lumber sizes. Beyond about 60 ft, expect engineered designs, larger chord sizes, and a sharp step up in price — the calculator’s top price band starts there.
What information does a truss plant need for an exact quote?
Building width (the span), length, roof pitch, overhang, ceiling and roof loads, and your snow/wind zone. Trusses are engineered per building and stamped by an engineer — no two plants quote the same job identically, which is why this calculator gives a range, not a single figure.
How far apart should roof trusses be spaced?
24 inches on center is the residential standard. Sixteen inches is used for heavy roofs (tile, slate, high snow load) or long spans; some engineered designs and metal roofs allow wider spacing. Spacing is set by the truss engineer, not preference — changing it changes the design.